manualshive.com logo in svg

Trane Sintesis Advantage CGAF 100 SE, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Trane Sintesis Advantage CGAF 100 SE Скачать руководство пользователя страница 80

80

CG-SVX039C-GB

Integrated Pump Maintenance

Water Pump Maintenance

WARNING!

 Before starting work on the pump, make sure 

that the power supply has been switched off and that it 
cannot be accidentally switched on.

CAUTION! 

The lifting eyebolts of the motor are suitable 

for the weight of the motor only. It is not allowed to carry 
the complete pump on the lifting eyebolts of the motor.

It is important to keep the motor clean in order to ensure 
adequate cooling of the motor. If the pump is installed 
in dusty environments, it must be cleaned and checked 
regularly. Take the enclosure class of the motor into 
account when cleaning.

If the water loop must be emptied during period of frost, 
the pump has to be drained to avoid damage. Remove 
the filling and drain plugs. Do not re-fit the plugs until 
the pump is taken into operation again.

Lubrication

The bearings of motors 5.5kW and 7.5kW are greased 
for life and require no lubrication. Increasing bearing 
noise and undue vibration indicate a worn bearing. The 
bearing or the complete motor then needs replacement. 

The bearing of motors 11kW and up must be greased 
every 4000 hours or at yearly service. The required 
grease quantity is 10g per bearing. The motor must run 
during lubrication. Use lithium-based grease.

The pump shaft seal does not require any special 
maintenance. Visual leakage check are however required. 
Distinctly visible leakage will require an exchange of the 
seal.

For further details about pump maintenance please 
consult the pump supplier website.

Figure 30 – Motor bearings

Содержание Sintesis Advantage CGAF 100 SE

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды