manualshive.com logo in svg

Trane Sintesis Advantage CGAF 100 SE, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Trane Sintesis Advantage CGAF 100 SE Скачать руководство пользователя страница 58

58

CG-SVX039C-GB

Total Heat Recovery

Figure 16 – Refrigerant Schematic THR option

THR should not be used for glycol application 
on evaporator side. Minimum THR start-up water 
temperature should be higher than 5°C. THR should be 
used when leaving evaporator temperature is between 5 
and 15.5°C.

Table 10 – Operating Map (THR) CGAF 080-190

Application

Standard 

ambient

High ambient

(°C)

(°C)

Min. outdoor air temperature

7.2

7.2

Max. outdoor air temperature

49

52

Min. leaving evaporator water 

temperature

4.4

4.4

Max. leaving evaporator 

water temperature

15.6

15.6

Min. leaving THR water 

temperature

30

30

Max. leaving THR water 

temperature

55

55

Figure 17 – Total Heat Recovery Operation Map

30 ,  33.0 

49 ,  52.0 

55 ,  52.0 

55 ,  7.2 

30 ,  7.2 

 -

 10.0

 20.0

 30.0

 40.0

 50.0

 60.0

 25

 30

 35

 40

 45

 50

 55

 60

Am

b T

em

pe

ra

tur

e 

(C

)

THR LWT (C)

THR 3-Way Valve Description

The 3-way valve is divided into 2 mains parts: the 
actuator and the valve body.

Valve body

2 types of valve are used (DN50, DN65) with a Kvs 
respectively of 40, **. 
Kvs –value is showing the capacity of media flow of a 
valve, it characterizes the volume flow (m3/h) of water 
by measuring a differential pressure (bar). This value is 
related to full stroke.
The 3-way valve body is connected to the system in 3 
points A, B, AB as below:

Actuator Overview 

- Supply voltage: 24 Vac
- Actuator setting 

•   W1(input signal failure): 100%, actuator will 

adjust to 100%  position when signal input fails 
(THR BP bypassed) 

•   W2(input signal range): LED “OFF” for 2~10V
•   W3 (direction of action): LED “ON” 2V for A-AB 

close, 10V for A-AB full open

Содержание Sintesis Advantage CGAF 100 SE

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды