manualshive.com logo in svg

Trane Sintesis Advantage CGAF 100 SE, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Trane Sintesis Advantage CGAF 100 SE Скачать руководство пользователя страница 79

CG-SVX039C-GB

79

Cleaning Procedures

It is mandatory to clean regularly the coils for a proper 
unit operation. Eliminate pollution and other residual 
material help to extend the life of the coils and the unit

CAUTION! Equipment Damage!

 Do not use coil cleaning 

agents to clean uncoated CGAF / CXAF coils. Use clean 
water only. Use of coil cleaning agents on uncoated 
CGAF / CXAF coils could cause damage to coils.
Regular coil maintenance, including frequent cleaning- 
enhances the unit’s operating efficiency by minimizing 
compressor head pressure and amperage draw. The 
condenser coil (non-coated and e-coated) should be 
cleaned at least once each quarter or more if the unit is 
located in a “dirty” or corrosive environment. Cleaning 
with cleansers or detergents is strongly discouraged due 
to the all-aluminium construction; straight water should 
prove sufficient. Any breach in the tubes can result in 
refrigerant leaks.

Important: 

Only in extreme cases should any type of 

chemical cleaner or detergent be used on micro channel 
coils. If it becomes absolutely necessary because water 
alone did not clean the coil, specify a cleaner that is:

•   A is pH neutral cleaner.
•   An alkaline cleaner that is no higher than 8 on 

the pH scale.

•   An acidic cleaner that is no lower than 6 on the 

pH scale.

•   Does not contain any hydrofluoric acids.

Be sure to follow the instructions provided with any 
cleaner chosen. Keep in mind that it is still MANDATORY 
that the coils are thoroughly rinsed with water after the 
application of the cleaner even if the instructions specify 
a “No Rinse” cleaner. Cleaners or detergents that are 
left on the coil due to improper rinsing will significantly 
increase the possibility of corrosion damage on the 
micro channel coil.

Note:

 Quarterly cleaning (or more for harsh 

environment) is essential to extend the life of a MCHE 
coil and is required to maintain warranty coverage. 
Failure to clean a MCHE coil will void the warranty and 
may result in reduced efficiency and durability in the 
environment.

WARNING!  Hazardous Voltage!

 Disconnect all electric 

power, including remote disconnects before servicing. 
Follow proper lockout/ tagout procedures to ensure the 
power cannot be inadvertently energized. Failure to 
disconnect power before servicing could result in death 
or serious injury.

1.  Disconnect Power to the unit.
2.  Wear proper personal protection equipment such 

as a face shield, gloves and waterproof clothing.

3.  Remove enough panels from the unit to gain safe 

access to the microchannel coil.

Note:

 It is better to clean the coil from the opposite 

direction of normal air flow (inside of unit out) because 
this allows the debris to be pushed out rather than 
forced further into the coil.

1.  Use a soft brush or vacuum to remove base debris 

or surface loaded fibers from both sides of the coil.

Note:

 Remove solid residue is essential to preserve 

performance of the coil and avoid corrosion over the 
length of the product life.

2.  Using a sprayer and water ONLY, clean the coil 

following the guidelines below.
a.  Sprayer nozzle pressure should not exceed 

40 bars.

b.  The maximum source angle should not exceed 

25 degrees (Figure 22) to the face of the coil. 
For best results spray the micro channel 
perpendicular to face of the coil.

c.  Spray nozzle should be approximately 5 to 

10 cm from the coil surface.

d.  Use at least a 15º fan type of spray nozzle.

Figure 29 – Sprayer source angle

To avoid damage from the spray wand contacting the 
coil, make sure the 90º attachment does not come in 
contact with the tube and fin as abrasion to the coil 
could result.

Maintenance of Flanges Connection

It is mandatory to apply marine grease all around the 
coil flange connections to the piping on a regular basis 
(for instance twice a year) to avoid traps of moisture and 
dirt in the gasket recess.

Repair / Replacement of 
Microchannel Coil

Microchannel coils are considerably more robust in 
design than tube and fin condenser coils, however they 
are not indestructible. When damage or a leak occurs in 
the field, it is possible to temporarily repair the coil until 
another coil can be ordered.
If the leak is found to be within the tube area of the coil, 
a field repair kit (KIT16112) is available through your 
local Trane parts center. Because of the all-aluminium 
construction and aluminium’s high thermal expansion 
rate, a leak located at or on the header assembly cannot 
be repaired.

Condenser Coils MCHE Maintenance

Содержание Sintesis Advantage CGAF 100 SE

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды