background image

Disassemble the Electric Box 

1.  Disassemble the left and right side board. After the grille is removed use a screwdriver to 

remove the screws shown in the picture. Push the side plate in the direction of the arrow and 
remove it. 

2.  Disassemble the right side board. 
3.  Disassemble the electric box cover. After the right side board is removed, the electric box 

cover will be exposed. Remove the fixed screws. 

General Maintenance

Regular checks, maintenance and care should be performed by professional personnel, which 
will prolong the unit life span.

Outdoor Heat Exchanger

The outdoor heat exchanger should be checked and cleaned once every two months. Use 
a vacuum cleaner with a nylon brush to clean up dust and debris on the surface of the heat 
exchanger. Blow away dust by compressed air if available. Never use water to wash the heat 
exchanger.

Drain Pipe

Regularly check to see if the drain pipe is clogged in order to ensure drain condensate doesn't 
overflow and cause water damage. 

Check Before Seasonal Use

1.  The inlet and outlet of the indoor and outdoor units are not clogged or obstructed. 
2.  The power and communication cables are securely attached and that there is no visible 

damage to any of the electrical wiring. 

3.  The batteries of the wireless remote controller have been replaced. 
4.  The filter screen has been cleaned and replaced securely. 
5.  After long periods of shutdown, open the main power switch 8 hours before operating the 

unit so as to preheat the compressor. 

6.  The outdoor and indoor units are installed securely. 
7.  If there is anything abnormal, please contact the installing dealer or qualified service 

technician. 

30

Floor and Ceiling Unit

Содержание 4MXX8509B10N0
































Отзывы: