TP-Link omada OC200 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 117

background image

82

Follow the steps below to configure Management Access on this page:

1. Check the box to enable

MAC Authentication

.

2. Specify one or more MAC addresses in the

MAC1/MAC2/MAC3/MAC4

fields. Up to

four MAC addresses can be added.

3. Click

Save

.

iipe

•

You can click

to quickly add the MAC address of your current logged-in host, .

•

Verify the MAC addresses carefully. Once the settings are saved, only the hosts in the MAC

address list can access the web page of the EAP.

•

If you cannot log in to the web page after saving the wrong configuration, you can reset the EAP

to the factory defaults and use the default username and password (both admin) to log in.

Configure Management VLAN

Management VLAN provides a safer method to manage the EAP. With Management VLAN
enabled, only the hosts in the Management VLAN can access the web page of the EAP.
Since most hosts cannot process VLAN TAGs, you can connect the management host to
the network via a switch, and set up correct VLAN settings for the switches on the network
to ensure the communication between the host and the EAP in the Management VLAN.

Follow the steps below to configure Management VLAN on this page:

1. Check the box to enable

Management VLAN

.

2. Specify the VLAN ID of the management VLAN. Only the hosts in the Management

VLAN can log in to the EAP via the Ethernet port.

3. Click

Save

.

«
...
84
85
86
87
88
...
»

Содержание omada OC200






















































































































Отзывы:

Нет отзывов

Похожие инструкции для omada OC200

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: IBM Страницы: 144

Бренд: Baby Trend Страницы: 10

Бренд: QCON Страницы: 4

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: HANYOUNG NUX Страницы: 56

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: Gardigo Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды