TP-Link omada OC200 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 117

background image

104

6.2

Build the Network Topology

Build the network topology as the following figure shows.

EAP

Management Host

Switch

Router (DHCP Server)

LAN: 192.168.88.1

Internet

•

The router is the gateway of the network and acts as a DHCP server to assign dynamic
IP addresses to the management host, EAP and clients. The LAN IP of the router is
192.168.88.1/24.

•

Connect the switch to the LAN port of the router.

•

Connect the management host and the EAP to the switch. The IP address mode of
the management host and EAP is dynamic, which means that they will get dynamic IP
addresses from the router.

iipe

If the router has more than one LAN port, we can also respectively connect the management host

and the EAP to the LAN ports of the router.

«
...
106
107
108
109
110
...
»

Содержание omada OC200






















































































































Отзывы:

Нет отзывов

Похожие инструкции для omada OC200

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: Samsung Страницы: 27

Flashlight Blue

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 4

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 5

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Lamtec Страницы: 136

Бренд: Zamel Страницы: 2

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренд: Data Signs Страницы: 23

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

Бренд: McIntosh Страницы: 60

Бренд: Ruida Technology Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды