TP-Link omada OC200 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 117

background image

75

•

Dynamic

If you choose Dynamic as the IP address mode, make sure that there is a reachable
DHCP server on your network and the DHCP sever is properly configured to assign IP
address and the other network parameters to the EAP.

For network stability, you can also configure the fallback IP parameters for the EAP:

Fallback IP

With the fallback IP configured, if the EAP fails to get an IP

address from a DHCP server within 10 seconds, the fallback

IP will work as the IP address of the EAP. After that, however,

the EAP will keep trying to obtain an IP address from the DHCP

server until it succeeds.

DHCP Fallback IP

Specify a fallback IP address for the EAP. Make sure that this IP

address is not being used by any other device in the same LAN.

The default DHCP fallback IP is 192.168.0.254.

DHCP Fallback IP MASK

Specify the network mask of the fallback IP. The default DHCP

fallback IP mask is 255.255.255.0.

DHCP Fallback Gateway

Specify the network gateway.

•

Static

If you choose Static as the IP address mode, you need to manually specify an IP
address and the related network parameters for the EAP. Make sure that the specified
IP address is not being used by any other device in the same LAN.

«
...
77
78
79
80
81
...
»

Содержание omada OC200






















































































































Отзывы:

Нет отзывов

Похожие инструкции для omada OC200

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 10

Бренд: Barco Страницы: 6

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Eaton Страницы: 288

Бренд: V2 ELETTRONICA Страницы: 72

Бренд: WAM Страницы: 62

Бренд: walimex Страницы: 7

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренд: Walchem Страницы: 126

Бренд: wallas Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: ABB Страницы: 17

Бренд: Parker Страницы: 38

Бренд: Parker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды