TP-Link omada OC200 Скачать руководство пользователя страница 53

Страница: 53 / 117

2.5

Configure Scheduler

With the Scheduler feature, the EAP or its wireless network can automatically turn on or
off at the time you set. For example, you can schedule the radio to operate only during the
office working time to reduce power consumption.

To configure Scheduler, go to the

Wireless > Scheduler

page.

Follow the steps below to configure Scheduler on this page:

1. In the

Settings

section, check the box to enable

Scheduler

and select the

Association

Mode

. There are two modes:

Associated with SSID

(the scheduler profile will be applied

to the specific SSID) and

Associated with AP

(the profile will be applied to all SSIDs on

the EAP). Then click

Save

Содержание omada OC200






















































































































Результаты поиска

Содержание omada OC200

Отзывы:

Похожие инструкции для omada OC200

Бренды по названию

Популярные бренды

TP-Link omada OC200, Руководство пользователя

Результаты поиска

Содержание omada OC200

Отзывы:

Похожие инструкции для omada OC200

Бренды по названию

Популярные бренды