TP-Link omada OC200 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 117

background image

52

2.6

Configure Band Steering

A client device that is capable of communicating on both the 2.4GHz and 5GHz frequency
bands will typically connect to the 2.4GHz band. However, if too many client devices
are connected to an EAP on the 2.4GHz band, the efficiency of communication will be
diminished. Band Steering can steer dual-band clients to the 5GHz frequency band which
supports higher transmission rates and more client devices, and thus to greatly improve
the network quality.

Ntte

Only the dual-band EAP products support Band Steering.

To configure Band Steering, go to the

Wireless > Band Steering

page.

Follow the steps below to configure Band Steering on this page:

1. Check the box to enable

Band Steering function.

2. Configure the following parameters to balance the clients on both frequency bands:

«
...
54
55
56
57
58
...
»

Содержание omada OC200






















































































































Отзывы:

Нет отзывов

Похожие инструкции для omada OC200

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: EA Страницы: 24

Бренд: GBD Страницы: 68

Бренд: Samson Страницы: 52

Бренд: Saga Страницы: 9

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: V2 ELETTRONICA Страницы: 72

Slim Remote Control

Бренд: Packard Bell Страницы: 2

Бренд: Unipower Страницы: 24

Grafica DNE-K07

Бренд: Paradox Страницы: 24

Бренд: Panosol Страницы: 105

Бренд: Pangolin Страницы: 8

Бренд: Parker Страницы: 4

Smart Control Panel 880RGD

Бренд: Raynor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды