TP-Link omada OC200 Скачать руководство пользователя страница 74

Страница: 74 / 117

3.3

Monitor the Clients

You can monitor the information of the clients connected to the EAP.

To monitor the client information, go to the

Status

Client

page.

View Client Information

There are two types of clients: users and portal authenticated guests. Users are the clients
that connect to the SSID with portal authentication disabled. Guests are the clients that
connect to the SSID with portal authentication enabled.

Click the

to select the client types to view the information of the EAP. The

following figure posted in the introduction takes user as an example.

The following client information is displayed:

Hostname

Displays the hostname of the user.

IP Address

Displays the IP address of the user.

Содержание omada OC200






















































































































Результаты поиска

Содержание omada OC200

Отзывы:

Похожие инструкции для omada OC200

Бренды по названию

Популярные бренды

TP-Link omada OC200, Руководство пользователя

Результаты поиска

Содержание omada OC200

Отзывы:

Похожие инструкции для omada OC200

Бренды по названию

Популярные бренды