manualshive.com logo in svg

Toyota 1NZ-FE, Руководство пользователя

Поделиться
Скачать
Toyota 1NZ-FE Скачать руководство пользователя страница 46

ENGINE - 1NZ-FE ENGINE

00REG22Y

To Intake Manifold

Purge VSV

Purge Air
Line

Fresh Air Line

Fuel Tank

Canister Filter

ECM

Canister Pump Module

Leak Detection 
Pump & Pump 
Motor

Canister 
Pressure Sensor

Refueling Valve

Vent 
Valve

Canister

M

P

EG-47

System Diagram

Function of Main Components

Component

Function

Canister

Contains activated charcoal to absorb the vapor gas that is created in
the fuel tank.

Refueling 

Controls the flow rate of the vapor gas from the fuel tank to the canister
when the system is purging or during refueling.

Refueling 
Valve

Restrictor 
Passage

Prevents a large amount of vacuum during purge operation or system
monitoring operation from affecting the pressure in the fuel tank.

Fresh Air Line

Fresh air goes into the canister and the cleaned drain air goes out into
the atmosphere.

C

i t

Vent Valve

Opens and closes the fresh air line in accordance with the signals from
the ECM.

Canister 
Pump 
Module

Leak Detection 
Pump

Applies vacuum pressure to the evaporative emission system in
accordance with the signals from the ECM.

Module

Canister 
Pressure Sensor

Detects the pressure in the evaporative emission system and sends the
signals to the ECM.

Purge VSV

Opens in accordance with the signals from the ECM when the system
is purging, in order to send the vapor gas that was absorbed by the
canister into the intake manifold. In system monitoring mode, this
valve controls the introduction of the vacuum into the fuel tank.

Canister Filter

Prevents dust and debris in the fresh air from entering the system.

ECM

Controls the canister pump module and purge VSV in accordance with
the signals from various sensors, in order to achieve a purge volume
that suits the driving conditions. In addition, the ECM monitors the
system for any leakage and outputs a DTC if a malfunction is found.

Содержание 1NZ-FE




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды