manualshive.com logo in svg

Toyota 1NZ-FE, Руководство пользователя

Поделиться
Скачать
Toyota 1NZ-FE Скачать руководство пользователя страница 23

ENGINE - 1NZ-FE ENGINE

206EG20

Conventional Type

Armature

Armature

B

B

A

A

PS Type

Brush

Commutator

Brush

Surface Commutator

Square-Shaped 
Conductor

Round-Shaped
Conductor

A - A Cross Section

(PS Type)

B - B Cross Section

(P Type)

222EG15

Main Magnet

Yoke

Interpolar Magnet

Main Magnet

Armature

Cross Section of Yoke

Magnetic Flux Generated by
Interpolar Magnets

N

S

N

N

S

S

Magnetic Flux Generated by 
Relationship Between Main Magnets

EG-24

2. PS (Planetary reduction-Segment conductor motor) Type Starter

Construction

Instead of constructing the armature coil with P type of round-shaped conductor wires, the PS type starter
uses square conductors. With this type of construction, the same conditions that are realized by winding
numerous round-shaped conductor wires can be achieved without increasing the mass. As a result, the
output torque has been increased, and the armature coil has been made compact.

Because the surface of the square-shaped conductors that are used in the armature coil functions as a
commutator, the overall length of the PS type starter has been shortened.

Instead of the field coils used in the P type starter, the PS type starter uses two types of permanent
magnets: the main magnets and the interpolar magnets. The main and interpolar magnets are arranged
alternately inside the yoke, allowing the magnetic flux that is generated between the main and interpolar
magnets to be added to the magnetic flux that is generated by the main magnets. In addition to increasing
the amount of magnetic flux, this construction shortens the overall length of the yoke.

Содержание 1NZ-FE




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды