manualshive.com logo in svg

Toyota 1NZ-FE, Руководство пользователя

Поделиться
Скачать
Toyota 1NZ-FE Скачать руководство пользователя страница 24

ENGINE - 1NZ-FE ENGINE

EG-25

ENGINE CONTROL SYSTEM

1. General

The engine control system for the 1NZ-FE engine has the following systems.

System

Outline

’06

Model

’05

Model

SFI

Electronic Fuel
Injection

An L-type EFI system detects the intake air mass with a
hot-wire type air flow meter.

ESA

Electronic Spark
Advance

Ignition timing is determined by the ECM based on signals
from various sensors. The ECM corrects ignition timing in
response to engine knocking.

ETCS-i

Electronic

Optimally controls the throttle valve opening in accordance
with the amount of accelerator pedal effort and the condition
of the engine and vehicle.

-

Electronic
Throttle Control
System-intelligent

See page EG-36

A linkless-type is used without an accelerator.

An accelerator pedal position sensor is provided on the
accelerator pedal.

A non-contact type throttle position sensor and accelerator
pedal position sensor are used.

-

VVT-i

Variable Valve
Timing-intelligent

See page EG-41

Controls the intake camshaft to optimal valve timing in
accordance with the engine condition.

Fuel Pump Control
See page EG-45

Fuel pump operation is controlled by signals from the ECM.

The operation of the fuel pump will stop when the airbag
is deployed.

Air Fuel Ratio Sensor
and Oxygen Sensor
Heater Control

Maintains the temperature of the air fuel ratio sensor or
oxygen sensor at an appropriate level to realize accuracy of
detection of the oxygen concentration in the exhaust gas.

-

Oxygen Sensor
Heater Control

Maintains the temperature of the oxygen sensor at an
appropriate level to realize accuracy of detection of the
oxygen concentration in the exhaust gas.

-

The ECM controls the purge flow of evaporative emissions
(HC) in the canister in accordance with engine conditions.

Evaporative
Emission

Using 3 VSVs and a vapor pressure sensor, the ECM detects any
evaporative emission leakage occurring between the fuel tank
and charcoal canister through changes in the fuel tank pressure.

-

Control
See page EG-46

Approximately five hours after the ignition switch has been
turned OFF, the ECM operates the canister pump module to
detect any evaporative emission leakage occurring in the
evaporative emission control system through changes in the
reference orifice pressure.

-

Air Conditioner
Cut-off Control*

1

By turning the air conditioner compressor OFF in accordance
with the engine condition, drivadility is maintained.

Cooling Fan Control
See page EG-56

Cooling fan operation is controlled by signals from ECM based
on the engine coolant temperature sensor signal (THW).

*

1

: for Models with Air Conditioning System

Содержание 1NZ-FE




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды