manualshive.com logo in svg

Toyota 1NZ-FE, Руководство пользователя

Поделиться
Скачать
Toyota 1NZ-FE Скачать руководство пользователя страница 34

ENGINE - 1NZ-FE ENGINE

00SEG39Y

228TU25

228TU24

A

A

Internal Construction

Accelerator 
Pedal Arm

Magnetic Yoke

Hall IC

A  - A Cross Section

Accelerator Pedal 
Position Sensor

Magnetic Yoke

Hall
IC

Hall
IC

VPA

EPA

VCPA

VPA2

EPA2

VCP2

ECM

V

5

0

Output 
Voltage

Fully 
Close

Fully 
Open

Accelerator Pedal Depressed Angle

VPA2

VPA

90

Service Tip

The inspection method differs from the conventional contact type accelerator pedal position sensor
because this non-contact type sensor uses a Hall IC.
For details, refer to the 2006 Yaris Repair Manual (Pub. No. RM00R0U).

EG-35

Accelerator Pedal Position Sensor

The non-contact type accelerator pedal position sensor used a Hall IC.

The magnetic yoke that is mounted at the accelerator pedal arm rotates around the Hall IC in accordance with
the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic
flux that occur at that time into electrical signals, and outputs them as of accelerator pedal effort to the ECM.

The Hall IC contains circuits for the main and sub signals. It converts the accelerator pedal depressing
angles into electric signals with two differing characteristics and outputs them to the ECM.

Содержание 1NZ-FE




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды