manualshive.com logo in svg

Toyota 1NZ-FE, Руководство пользователя

Поделиться
Скачать
Toyota 1NZ-FE Скачать руководство пользователя страница 14

ENGINE - 1NZ-FE ENGINE

00REG03Y

Charcoal Filter

Air Cleaner Cap

Air Cleaner Element
(Nonwovens Fabric)

Service Tip

The charcoal filter, which is maintenance-free, cannot be removed from the air cleaner cap.

00REG04Y

DC Motor

Throttle Valve

Reduction Gears

Throttle Position Sensor

EG-15

2. Air Cleaner

A nonwoven, full-fabric type air cleaner element is used.

A charcoal filter, which adsorbs the HC that accumulates in the intake system when the engine is stopped,
is used in the air cleaner cap in order to reduce evaporative emissions.

3. Throttle Body

The linkless-type throttle body is used and it realizes excellent throttle control.

A DC motor with excellent response and minimal power consumption is used for the throttle control motor.
The ECM performs the duty ratio control of the direction and the amperage of the current that flows to
the throttle control motor in order to regulate the opening angle of the throttle valve.

Содержание 1NZ-FE




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды