manualshive.com logo in svg

Toyota 1NZ-FE, Руководство пользователя

Поделиться
Скачать
Toyota 1NZ-FE Скачать руководство пользователя страница 38

ENGINE - 1NZ-FE ENGINE

199EG45

ECM

Accelerator Pedal
Position Sensor

Main

Sub

Accelerator Pedal

Throttle Body

Open

Main

Sub

Throttle
Position
Sensor

Throttle
Valve

Return 
Spring

Throttle
Control
Motor

199EG46

ECM

Accelerator Pedal
Position Sensor

Main

Sub

Accelerator Pedal

Throttle Body

Main

Sub

Throttle
Position
Sensor

Throttle
Valve

Return 
Spring

Throttle
Control
Motor

Close by 
Return Spring

EG-39

Fail-Safe of Accelerator Pedal Position Sensor

The accelerator pedal position sensor is comprised of two (main, sub) sensor circuits. If a malfunction
occurs in either one of the sensor circuits, the ECM detects the abnormal signal voltage difference
between these two sensor circuits and switches to the limp mode. In the limp mode, the remaining circuit
is used to calculate the accelerator pedal depressed angle, in order to operate the vehicle under limp mode
control.

If both circuits have malfunctions, the ECM detects the abnormal signal voltage from these two sensor
circuits and discontinues the throttle control. At this time, the vehicle can be driven within its idling
range.

Содержание 1NZ-FE




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды