manualshive.com logo in svg

Toyota 1NZ-FE, Руководство пользователя

Поделиться
Скачать
Toyota 1NZ-FE Скачать руководство пользователя страница 42

ENGINE - 1NZ-FE ENGINE

169EG36

Housing

Lock Pin

Intake Camshaft

Vane (Fixed on Intake Camshaft)

Oil Pressure

At a Stop

In Operation

Lock Pin

221EG17

to VVT-i Controller 
(Advance Side)

Sleeve

Spring

Drain

Oil Pressure

Drain

to VVT-i Controller 
(Retard Side)

Spool Valve

Coil

Plunger

EG-43

Construction

1) VVT-i Controller

This controller consists of the housing driven from the timing chain and the vane coupled with the intake
camshaft.
The oil pressure sent from the advance or retard side path at the intake camshaft causes rotation in the
VVT-i controller vane circumferential direction to vary the intake valve timing continuously.
When the engine is stopped, the intake camshaft will be in the most retarded state to ensure startability.
When hydraulic pressure is not applied to the VVT-i controller immediately after the engine has been
started, the lock pin locks the movement of the VVT-i controller to prevent a knocking noise.

2) Camshaft Timing Oil Control Valve

This camshaft timing oil control valve controls the spool valve position in accordance with the duty-cycle
control from the ECM. This allows hydraulic pressure to be applied to the VVT-i controller advance or
retard side. When the engine is stopped, the camshaft timing oil control valve is in the most retarded state.

Содержание 1NZ-FE




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды