background image

43-EN

44-EN

– 22 –

Wired 

remote 

controller 

display

Wireless remote controller

Sensor block display of 

receiving unit

Main defective parts

Judging 

device

Parts to be checked /

error description

Air 

conditioner 

status

Indication

Operation 

Timer Ready

GR GR OR

Flashing

F10

ALT

Indoor unit room temp. 
sensor (TA) error

Indoor

Room temp. sensor (TA), indoor P.C. board 
--- Open-circuit or short-circuit of the room 
temp. sensor (TA) was detected.

Auto-reset

F12

ALT

TS sensor error

Outdoor

TS sensor may be displaced, disconnected 
or short-circuited.

Entire stop

F13

ALT

Heat sink sensor error

Outdoor

Abnormal temperature was detected by the 
temp. sensor of the IGBT heat sink.

Entire stop

F15

ALT

Temp. sensor 
connection error

Outdoor

Temp. sensor (TE / TS) may be connected 
incorrectly. 

Entire stop

F29

SIM

Indoor unit, other P.C. 
board error

Indoor

Indoor P.C. board --- EEPROM error. 

Auto-reset

F31

SIM

Outdoor unit P.C. board

Outdoor

Outdoor P.C. board ---- In the case of 
EEPROM error.

Entire stop

H01

Outdoor unit 
compressor breakdown

Outdoor

Current detect circuit, power voltage --- 
Minimum frequency was reached in the 
current releasing control or short-circuit 
current (Idc) after direct excitation was 
detected.

Entire stop

H02

Outdoor unit 
compressor lock

Outdoor

Compressor circuit --- Compressor lock 
was detected.

Entire stop

H03

Outdoor unit current 
detect circuit error

Outdoor

Current detect circuit, outdoor unit P.C. 
board --- Abnormal current was detected in 
AC-CT or a phase loss was detected.

Entire stop

H04

Case thermostat 
operation

Outdoor

Malfunction of the case thermostat

Entire stop

H06

Outdoor unit 
low-pressure system 
error

Outdoor

Current, high-pressure switch circuit, 
outdoor P.C. board --- Pressure sensor 
error was detected or low-pressure 
protective operation was activated.

Entire stop

L03

SIM

Duplicated header 
indoor units 

Indoor

Indoor address setting error --- There are 
two or more header units in the group.

Entire stop

L07

SIM

Group line in individual 
indoor unit 

Indoor

Indoor address setting error --- There is 
at least one group-connected indoor unit 
among individual indoor units.

Entire stop

L08

SIM

Indoor group address 
not set 

Indoor

Indoor address setting error --- Indoor 
address group has not been set. 

Entire stop

L09

SIM

Indoor unit capacity 
not set

Indoor

Indoor unit capacity has not been set.

Entire stop

L10

SIM

Outdoor unit P.C. board

Outdoor

In the case of outdoor P.C. board jumper 
wire (for service) setting error.

Entire stop

L20

SIM

LAN communication 
error

Network 
adapter 
central 
control

Address setting, central control remote 
controller, network adapter ---
Duplication of address in central control 
communication.

Auto-reset

L29

SIM

Other outdoor unit error

Outdoor

Other outdoor unit error.

Entire stop

1) Communication error between IPDU 
MCU and CDB MCU.

Entire stop

2) Abnormal temperature was detected by 
the heat sink temp. sensor in IGBT.

L30

SIM

Abnormal external 
input into indoor unit 
(interlock)

Indoor

External devices, outdoor unit P.C.
board --- Abnormal stop due to incorrect 
external input into CN80.

Entire stop

L31

SIM

Phase sequence error, 
etc.

Outdoor

Power supply phase sequence, outdoor unit 
P.C. board --- Abnormal phase sequence of 
the 3-phase power supply.

Operation 
continued 
(thermostat 
OFF)

P01

ALT

Indoor unit fan error

Indoor

Indoor fan motor, indoor P.C. board ---
Indoor AC fan error (fan motor thermal relay 
activated) was detected.

Entire stop

Wired 

remote 

controller 

display

Wireless remote controller

Sensor block display of 

receiving unit

Main defective parts

Judging 

device

Parts to be checked /

error description

Air 

conditioner 

status

Indication

Operation 

Timer Ready

GR GR OR

Flashing

P03

ALT

Outdoor unit discharge 
temp. error

Outdoor

An error was detected in the discharge 
temp. releasing control.

Entire stop

P04

ALT

Outdoor unit 
high-pressure system 
error

Outdoor

High-pressure switch --- The IOL was 
activated or an error was detected in the 
high-pressure releasing control using the 
TE.

Entire stop

P05

ALT

Open phase detected

Outdoor

The power wire may be connected 
incorrectly. Check open phase and voltages 
of the power supply.

Entire stop

P07

ALT

Heat sink overheat

Outdoor

Abnormal temperature was detected by the 
temp. sensor of the IGBT heat sink.

Entire stop

P10

ALT

Indoor unit water 
over

fl

 ow detected

Indoor

Drain pipe, clogging of drainage, 

fl

 oat 

switch circuit, indoor P.C. board ---
Drainage is out of order or the 

fl

 oat switch 

was activated.

Entire stop

P12

ALT

Abnormal operation of 
the fan of the indoor unit

Indoor

Abnormal operation of the indoor fan motor, 
indoor P.C. board, or indoor DC fan (over 
current or lock, etc.) is detected.

Entire stop

P15

ALT

Gas leakage detected

Outdoor

There may be gas leakage from the pipe or 
connecting part. Check for gas leakage.

Entire stop

P19

ALT

 4-way valve error

Outdoor 
(Indoor)

4-way valve, indoor temp. sensors (TC /
TCJ) --- An error was detected due to 
temperature drop of the indoor unit heat 
exchanger sensor during heating.

Auto-reset

P20

ALT

High-pressure protective 
operation

Outdoor

High-pressure protection. 

Entire stop

P22

ALT

Outdoor unit fan error

Outdoor

Outdoor unit fan motor, outdoor unit P.C. 
board --- An error (overcurrent, locking, 
etc.) was detected in the outdoor unit fan 
drive circuit.

Entire stop

P26

ALT

Outdoor unit inverter Idc 
activated

Outdoor

IGBT, outdoor unit P.C. board, inverter 
wiring, compressor --- Short-circuit 
protection for compressor drive circuit 
devices (G-Tr / IGBT) was activated.

Entire stop

P29

ALT

Outdoor unit position 
error

Outdoor

Outdoor unit P.C. board, high-pressure 
switch --- Compressor motor position error 
was detected.

Entire stop

P31

ALT

Other indoor unit error

Indoor

Another indoor unit in the group is raising 
an alarm.

Entire stop

E03 / L07 / L03 / L08 alarm check locations 
and error description.

Auto-reset

: Lighting   : Flashing   : OFF   : The air conditioner automatically enters the auto-address setting mode.

ALT: When two LEDs are 

fl

 ashing, they 

fl

 ash alternately. SIM: When two LEDs are 

fl

 ashing, they 

fl

 ash in synchronization.

Receiving unit display OR: Orange GR: Green

1111056499_(01)_EN.indb   22

1111056499_(01)_EN.indb   22

10/13/14   9:13 AM

10/13/14   9:13 AM

Содержание RAV-SM307KRTP-E

























Отзывы: