Toshiba RAV-SM307KRTP-E, Руководство по установке

Страница: 13 / 24

23-EN 24-EN
– 12 –
Screw
Terminal block for
Indoor / Outdoor
connecting
Terminal block for wired
remote controller /
Central control
Earth screw
Screw
Cord clamp
Terminal
cover
Terminal block
for Indoor / Outdoor
connecting wiring
Cord clamp
Earth screw
Wired remote
controller wire
◆ Wiring diagram
A
B
A
B
Terminal block for
remote controller
wiring of Indoor unit
Terminal block
Remote
controller
unit
Remote controller wire
(locally procured)
11
Applicable
controls
REQUIREMENT
• When this air conditioner is used for the fi rst time, it
takes approx. 5 minutes until the remote controller
becomes available after power-on. This is normal.
<When power is turned on for the fi rst time
after installation>
It takes approx. 5 to 10 minutes until the remote
controller becomes available.
Approx. 5 minutes
Power on
“SETTING”
fl ashes
“SETTING”
goes out
Remote
controller is
available
<When power is turned on for the second (or
later) time>
It takes approx. 1 minute until the remote
controller becomes available.
Approx. 1 minutes
Power on
“SETTING”
fl ashes
“SETTING”
goes out
Remote
controller is
available
• Normal settings were made as factory default.
Change the indoor unit settings as required.
•
Use the wired remote controller to change the
settings.
* The settings cannot be changed using the
wireless remote controller, simple wired remote
controller, or remote-controller-less system
(for central remote controller only). Therefore,
install the wired remote controller to change the
settings.
■
Basic procedure for changing
settings
Change the settings while the air conditioner is not
working.
(Stop the air conditioner before making settings.)
CAUTION
Set only the CODE No. shown in the following table:
Do NOT set any other CODE No.
If a CODE No. not listed is set, it may not be possible
to operate the air conditioner or other trouble with the
product may result.
* The displays appearing during the setting process
differ from the ones for previous remote controllers
(AMT31E). (there are more CODE No.)
1
6
1
3
2 5
4
1
Push button and TEMP. button
simultaneously for 4 seconds or more.
After a while, the display fl ashes as shown in the
fi gure.
Con fi rm that the CODE No. is [01].
•
If the CODE No. is not [01], push button
to erase the display content, and repeat the
procedure from the beginning.
(No operation of the remote controller is
accepted for a while after button is pushed.)
(* Display content varies with
the indoor unit model.)
2
Each time button is pushed, indoor
unit numbers in the control group change
cyclically. Select the indoor unit to change
settings for.
The fan of the selected unit runs. The indoor unit
can be con
fi rmed for which to change settings.
3
Specify CODE No. [ ] with TEMP. /
buttons.
4
Select SET DATA [ ] with TIME /
buttons.
5
Push button. When the display changes
from fl ashing to lit, the setup is completed.
•
To change settings of another indoor unit,
repeat from Procedure
2
.
•
To change other settings of the selected indoor
unit, repeat from Procedure
3
.
Use button to clear the settings.
To make settings after button was pushed,
repeat from Procedure
2
.
6
When settings have been completed, push
button to determine the settings.
When button is pushed, “SETTING” fl ashes
and then the display content disappears and the
air conditioner enters the normal stop mode.
(While “SETTING” is
fl ashing, no operation of the
remote controller is accepted.)
1111056499_(01)_EN.indb 12 1111056499_(01)_EN.indb 12 10/13/14 9:13 AM 10/13/14 9:13 AM