29-EN
30-EN
– 15 –
[Procedure example]
Manual address setup procedure
While the operation stops, change the setup.
(Stop the operation of the unit.)
2,6
1
7
3
-1,
4
5
6
-1,
-1,
7
3
-3,
4
-3,
3
-2,
4
-2,
5
-2
5
-3,
1
Push + + buttons simultaneously
for 4 seconds or more. After a while, the
display part
fl
ashes as shown below.
Check the displayed CODE No. is [10].
•
When the CODE No. is other than [
10
], push
button to erase the display and repeat
procedure from the
fi
rst step.
(After pushing button, operation of the
remote controller is not accepted for approx.
1 minute.)
(For a group control, No. of the firstly displayed
indoor unit becomes the header unit.)
(* Display changes according to the
model No. of indoor unit.)
2
Every
time
button is pushed, the
indoor UNIT No. in the group control is
displayed in order. Select the indoor unit of
which setup is changed.
In this time, the position of the indoor unit of which
setup is changed can be con
fi
rmed because fan
of the selected indoor unit operate.
3
1) Specify CODE No. [12] with TEMP.
/
buttons.
(CODE No. [12]: Line address)
2) Change the line address from [3] to [2] with
TIME
/
buttons.
3) Push button.
In this time, the setup finishes when the
display changes from flashing to lighting.
Indoor unit No. before setup change is displayed.
4
1) Specify CODE No. [13] with TEMP.
/
buttons.
(CODE No. [13]: Indoor address)
2) Change the indoor address from [3] to [2]
TIME
/
buttons.
3) Push button.
In this time, the setup finishes when the
display changes from flashing to lighting.
Indoor unit No. before setup change is displayed.
5
1) Specify CODE No. [14] TEMP.
/
buttons.
(CODE No. [14]: Group address)
2) Change the SET DATA from [0001] to [0002]
TIME
/
buttons.
(SET DATA [Header unit: 0001] [Follower
unit: 0002])
3) Push button.
In this time, the setup finishes when the
display changes from flashing to lighting.
Indoor unit No. before setup change is displayed.
6
If there is other indoor unit to be changed,
repeat procedure
2
to
5
to change the
setup.
When the above setup has
fi
nished, push
to select the indoor UNIT No. before change of
setup, specify CODE No. [
12
], [
13
], [
14
] in order
with TEMP.
/
buttons, and then check the
changed contents.
Address change check Before change:
[
3-3-1
]
→
After change: [
2-2-2
]
Pushing button clears the contents of which
setup was changed.
(In this case, procedure from
2
is repeated.)
Indoor UNIT No. before setup change is displayed.
7
After check of the changed contents, push
button. (setup is determined.) When
button is pushed, the display disappears
and the status becomes the usual stop
status. (when button is pushed the
operation from the remote controller is not
accepted for approx. 1 minute.)
*
If the operation from the remote controller is
not accepted even 1 minute or more passed
after pushing button, it is considered that the
address setup is incorrect.
In this case, the automatic address must be
again set up.
Therefore repeat procedure of the setup change
from the Procedure
1
.
To recognize the position of the
corresponding indoor unit though the
indoor UNIT No. is known
Check the position during operation stop.
(Stop operation of the set.)
2
1,3
1
1
Push +
buttons simultaneously for
4 seconds or more.
After a while, the display part
fl
ashes and the
display appears as shown below.
In this time, the position can be checked
because fan of the indoor unit operate.
•
For the group control, the indoor UNIT No. is
displayed as [
] and fans of all the indoor
units in the group control operate.
Check the displayed CODE No. is [
01
].
•
When the CODE No. is other than [
01
], push
button to erase the display and repeat procedure
from the
fi
rst step.
(After pushing button, operation of the remote
controller is not accepted for approx. 1 minute.)
(* Display changes according to the
model No. of indoor unit.)
2
In the group control, every time
button is pushed, the indoor UNIT No. in
the group control is displayed in order.
In this time, the position of the indoor unit can be
confirmed because only fan of the selected indoor
unit operate.
(For a group control, No. of the
fi
rstly displayed
indoor unit becomes the header unit.)
3
After
con
fi
rmation, push button to return
the mode to the usual mode.
When button is pushed, the display disappears
and the status becomes the usual stop status.
(When button is pushed the operation from the
remote controller is not accepted for approx.
1 minute.)
1111056499_(01)_EN.indb 15
1111056499_(01)_EN.indb 15
10/13/14 9:13 AM
10/13/14 9:13 AM
