Toshiba G2020 Series Скачать руководство пользователя страница 79

Страница: 79 / 86

G2020 Series UPS Installation and Operation Manual

– 94861-004

Installation Planning Guide for 750kVA UPS

Single Module System: 480V Input, 480V Output

General Mechanical Information

Dimensions
(W x D x H)

Weight

Floor

Approximate Full-Load
Heat Rejection

Mechanical Clearance (Inches)from UPS
for Ventilation and Maintenance Access

Inches

Lbs.

Lbs./ft.

BTU/Hr

Top

Front

Bottom

Sides**

Back

81.6

” x 33.5” x 80.6”*

3,990

211

62,392

”

0”

* Height includes removable fan housing

– Frame height is 78.7”.

** 0” clearance for peripheral equipment, 1” clearance for walls.

Primary AC Input (480V 3-Phase / 3-Wire)

Maximum Input Power Demand
Normal Mode (Recharge Mode)

Recommended External

Overcurrent Protection

External Feeder Wire Size Per Phase:

kVA

Amps (Max.)

Amps

Cable Quantity of Below kcmil at 75º C Temp. Rating

250kcmil

300kcmil

350kcmil

400kcmil

500kcmil

600kcmil

781 (840)

>0.99

939 (1010)

1300AT (1600AF)

Alternate (Bypass) AC Input (480V 3-Phase / 3-Wire)

Input Power Demand

Recommended External

Overcurrent Protection

External Feeder Wire Size Per Phase:

kVA

Amps (Max.)

Amps

Cable Quantity of Below kcmil at 75º C Temp. Rating

250kcmil

300kcmil

350kcmil

400kcmil

500kcmil

600kcmil

750

1.0

902A

1200AT

Battery Input (480VDC Nominal)

Battery Capacity Required

for Full Load Output

Maximum Discharge at

Full Load Output

Recommended External

Overcurrent Protection

External Feeder Wire Size:

kWB

Amps DC

Amps

Cable Quantity of Below kcmil at 75º C Temp. Rating

250kcmil

300kcmil

350kcmil

400kcmil

500kcmil

600kcmil

776 @ 1.0 PF

1,940A

2500AT

AC Output (480V 3-Phase / 3-Wire)

Rated Output Power

Recommended External

Overcurrent Protection

External Feeder Wire Size Per Phase:

kVA

Amps

Cable Quantity of Below kcmil at 75º C Temp. Rating

250kcmil

300kcmil

350kcmil

400kcmil

500kcmil

600kcmil

750

1.0

902

1200 AT

Important Notes:
1.

Maximum input current is limited to 108% of the rated input current.

Output load conductors are to be installed in separate conduit from
input conductors.

Control wires and power wires are to be installed in separate
conduits.

Recommended AC input and output overcurrent protection based
on continuous full load current per NEC 215.3.

Wiring shall comply with all applicable national and local electrical
codes.

Grounding conductors to be sized per NEC Article 250-122.

Primary AC Input: 3



, 3-wire + ground.

Alternate AC Input: 3



, 3-wire + ground.

AC Output: 3



, 3-wire + ground.

DC Input: 2-wire (Positive/Negative) + ground.

Nominal battery voltage based on the use of VRLA type batteries

(2.0 volts/cell nominal).

Maximum battery discharge current based on lowest permissible

discharge voltage of 1.67 VPC.

DC wires should be sized to allow not more than a 2-volt drop at

maximum discharge current.

10. Weights do not include batteries or other auxiliary equipment external

to the UPS.

11. Cable sizing calculations based on the following method:



Base cable ampacity is determined by 75

C rated copper

conductor values in 2014 NEC Table 310.15(B)(16).



Cable ampacity is derated for 40

C Ambient Operating

Temperature per 2014 NEC Table 310.15(B)(2)(a).



Cable ampacity is further derated for maximum possible of

conductors in Trade Size 4” EMT conduit per quantities shown in
2014 NEC Table C.1 and factors shown in Table 310.15(B)(3)(a).



Cable meets bend radius limitations at the UPS terminals.

NOTE: Consult latest edition of applicable national and local
codes for possible variations.

12. Ratings of wires and overcurrent devices are suggested minimums.

Consult with a registered Professional Engineer within your local area
for proper size selections.

13. Overcurrent protection devices rated at 1200AT and above are

assumed to be rated for 100% continuous operation.

Содержание G2020 Series























































































Результаты поиска

Содержание G2020 Series

Отзывы:

Toshiba G2020 Series, Инструкция по установке и эксплуатации, Страница: 79 / 86

Результаты поиска

Содержание G2020 Series

Отзывы: