Toshiba G2020 Series Скачать руководство пользователя страница 46

Страница: 46 / 86

G2020 Series UPS Installation and Operation Manual

– 94861-004

INSTALLATION AND OPERATION

5.1

TRANSPORTATION AND INSTALLATION

Transport with forklift. If carry by overhead crane, use four eyebolts (Not provided)

Table 5-1 Transport by Overhead Crane

Model

UPS Cabinet

Landing Cabinet *

500kVA

4 x M20 Lifting Eyes

4 x M16 Lifting Eyes

750kVA

4 x M24 Lifting Eyes

4 x M16 Lifting Eyes

* Use lifting eyes on landing cabinet only to lift landing cabinet by itself, not as part of assembled unit.

Install the unit using the four pre-drilled holes in the UPS channel base. Anchor the unit using appropriate hardware. (Not

provided).

Do not transport UPS cabinet laid horizontally.

Cabinets must be maintained upright within ± 15

of the vertical during handling.

5.2

INSTALLATION PROCEDURE

A) Note the load tolerance of the floor

Refer to Table 5-2 for list of UPS weights.

Table 5-2 List of UPS Weights

UPS Capacity (kVA)

500

750

Weight (lb.)

2,756

3,990

B) Minimum clearance required for ventilation

Right side

1 in. (25 mm) (not required when sidecars are used)

Left side

1 in. (25 mm) (not required when sidecars are used)

Back side

0.0 in. (0 mm)

Top side

24 in. (610 mm) (for air flow)

C) Space requirement for routine maintenance

Allow for the following space at the time of installation.

Front

40 in. (1016 mm)

Sides

0.0 in. (0 mm)

Back side

0.0 in. (0 mm)

Top side

20 in. (500 mm)

PROHIBIT

NOTE

Содержание G2020 Series























































































Результаты поиска

Содержание G2020 Series

Отзывы:

Похожие инструкции для G2020 Series

Бренды по названию

Популярные бренды

Toshiba G2020 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание G2020 Series

Отзывы:

Похожие инструкции для G2020 Series

Бренды по названию

Популярные бренды