Toshiba G2020 Series Скачать руководство пользователя страница 13

Страница: 13 / 86

G2020 Series UPS Installation and Operation Manual

– 94861-004

The UPS is to be installed in a controlled environment.

Improper storage and installation environment may deteriorate insulation, shorten component life and cause
malfunctions.

Keep the installation environment per standard described as follows:

Table 2-1 UPS Installation Environment

Item

Environment standard

Installation

Location

Indoors

Ambient

temperature

Minimum temperature: 32



F (0



Maximum temperature: 104



F (40



The average temperature over any 24-hour period must be in the range



F (5



C) to 95



F (35



C).

Relative

humidity

The relative humidity must be held between 5 and 95%.

There must be no condensation due to temperature changes.

Altitude

This equipment is designed to operate without derating at 1980m (6500ft)

above sea level.

Dust

Dust in the room where the UPS is installed must not exceed normal

atmospheric dust levels. In particular, that dust should not include iron

particles, oils or fats, or organic materials such as silicone.

Inflammable

gas

following

IEC654-4

Part 4

There should be no inflammable/explosive gas.

Hydrogen sulfide (H

No more than 0.003 PPM

Sulfurous acid gas (SO

)

No more than 0.01 PPM

Chlorine gas (Cl

)

No more than 0.002 PPM

Ammonia gas (NH

)

No more than 1 PPM

Nitrous oxides (NO

)

No more than 0.05 PPM

Ozone (O

)

No more than 0.002 PPM

WARNING 3

WARNING

Содержание G2020 Series























































































Результаты поиска

Содержание G2020 Series

Отзывы:

Toshiba G2020 Series, Инструкция по установке и эксплуатации, Страница: 13 / 86

Результаты поиска

Содержание G2020 Series

Отзывы: