Toshiba ESTIA R32 HWT-1101F21MT6W-E, Руководство пользователя

Страница: 89 / 92

TOSHIBA I 49 TOSHIBA I 49
KNX module
IMPORTANT:
•
Only ever use one remote control. No additional remote controls can be used if you
connect this interface.
• You cannot connect or mix Hydroboxes from series 4 and series 5.
Specification
Part Specification value
Power supply unit KNX line 29 VDC / 8 mA
AW line 14 VDC / 20 mA
Operating temperature and humidity 0°C to 40°C 10 to 80% RH (non-condensing)
Storage temperature and humidity -20°C to 60°C 10 to 80% RH (non-condensing)
Casing material Sheet metal box: galvanized sheet iron (SGCC-CSC) base 0.8 t; cover 0.6 t;
no coating; forming unit ABS (UL 94 HB) 2.5 mm thick
Size Sheet metal box 33.4 (H) x 82.5 (W) x 92.1 (D) mm
Forming unit 28 (H) x 70 (W) x 70 (D) mm
Weight 225 g (including sheet metal box) 70 g (forming unit)
Supplied items
No . Part designation Quantity Comments
1 KN interface (forming unit) 1
2 Operating instructions 1
3 Sheet metal box 1 Cover, base
4 Fastening screws
Use the following wiring material to connect the signal lines (to be procured on site)
No . Cable Part Value
1 For KNX TP-1 bus Cable type KNX TP1
Cable diameter
Cable length
1000 m
Polarity Yes (+/-)
2 For AB bus (AW-LINK) lines Cable type VCTF
Cable diameter 0.5 mm
2
to 2.0 mm
2
Cable length 50 m (0.75
2
)
Polarity No
KN Interface Installation Manual
2 -EN
Safety instructions
WARNING
Follow carefully these safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the interface
and/or the Hydro unit.
• This interface must be installed by accredited technical personnel (electrician, KNX installer, or technical personnel) and following all the safety instructions.
• This interface must only be installed in a restricted access location.
• Before manipulating the Hydro unit, be sure it is completely disconnected from Mains power.
• Do not modify the unit. (A fire or an electric shock may occur)
• This interface must only be installed in a restricted access location by user.
• Do not install the unit in any of the following places.
• Humid or wet place
• Dusty place
• Place exposed to direct sunlight
• Place where there is a TV set or radio within one meter
• Place exposed to rain (outdoors, under eaves, etc.)
• Use predefined cable and connect them certainly. Keep the connecting terminal free from external force.
It may cause an exothermic or a fire.
• Strip the insulation from the cable that connects to the connector (KNX and A B bus) following the dimensions shown in the diagram below.
• When connecting the cable to the connector (KNX and A B bus), ensure the core wires do not protrude from the connector.
• Use two-core cabtyre cable.
• Disconnect the KNX bus from power before manipulate it and connect it to the interface.
• To prevent EMC disturbances, ensure that there is a safety separation (SELV) of the connected signal cables (including possible extensions) from the other
voltage carrying devices and cables.
Installation instructions
• Disconnect the Hydro unit from Mains Power.
• Disconnect the power supply of the KNX bus.
• Connect the connection cable between the interface and the Hydro unit following the instructions of the diagram below.
• Connect the KNX bus to the connector KNX of the interface. Respect the polarity.
• Close the Hydro unit and reconnect it to Mains Power.
• Reconnect power supply to the KNX bus.
• Follow the instructions on the user's manual for configuring and commissioning the interface. See below how to obtain the user's manual and the ETS database.
IMPORTANT:
• Use only one remote controller. A sub-remote controller cannot be connected when connecting this interface.
• It is not possible to mix and connect Hydro unit 4 series and 5 series.
NOTE
The cable used for connection of BMS-IFKX0AWR-E to A B bus can be any two-core cabtyre cable, the maximum distance for bus A B is 50 meters, consult the
manual of the Hydro unit for more details.
NOTE
In its place there is a pair of cables to connect the Remote Controller. Use these cables to connect the AB bus. Check your Hydro unit user or service manual for
more information.
A
TB07
B
(20 mm) (5 mm)
Hydro Unit
The terminal
block in the
hydro unit.
Connection to A B bus.
Two-core cabtyre cable.
Length of stripped KNX and A B bus communication
cable
Max. 50m
KNX TP-1
(EIB) bus
KNX MODULE