65/5560 ADJUSTMENT
MAY.1997 © TOSHIBA CORP.
2-9
2.5.2 Output Signal check (03/04)
In the "03"or"04"test mode,the folloeing output signal conditions can be checked by entering appropiate
codes.
Code Function
Stop code
1
DRM-MOT
ON
11
OFF
2
FED-MOT
ON
12
OFF
3
RGT-MOT
ON
13
OFF
4
HTR-MOT
ON
14
OFF
5
DEV-MOT
ON
15
OFF
6
TNR-MOT
ON
16
OFF
7
OPT-FAN-MOT
HIGH
17
LOW
8
EXIT-FAN-MOT
HIGH
18
LOW
9
AUG-MOT
ON
19
OFF
41
ADD-FED-MOT
ON
51
OFF
42
ADD-RGT-MOT(Stack) ON
52
OFF
43
ADD-RGT-MOT(Feed)
ON
53
OFF
61
PD-MOT
ON
71
OFF
62
FD2-CLT
FD3-CLT
ON
72
OFF
FD4-CLT
63
RGT2-CLT
RGT3-CLT
ON
73
OFF
RGT4-CLT
65
DEV-FAN
ON
75
OFF
67
BTM-FAN
HIGH
77
LOW
68
CH-FAN
HTR-FAN
ON
78
OFF
20
SCN-MOT
21
LNS-MOT
22
MRR-MOT
23
CLN-MOT
24
DCM-MOT
25
CLN-TR-MOT
Changes direction
26
TRAY-MOT(LCF)
each time the PRINT
45
STOP-MOT
key is pressed.
46
GUIDE-MOT
64
TR2-MOT(PFP)
TR3-MOT(PFP)
TR4-MOT(PFP)
*8
Group3
Code
Function
30
HV-M
ON/OFF
(Main charger output)
31
HV-TR
ON/OFF
(Transfer charger output)
32
HV/AC
ON/OFF
(Transfer charger output)
33
EXP-LAMP
ON/OFF
34
GBIAS
ON/OFF
(Transfer bias output)
35
PRE-TR-C4
ON/OFF
37
SCRP-SOL
ON/OFF
38
MANUAL-SOL
ON/OFF
48
ADD-SOL
ON/OFF
49
GATE-SOL
ON/OFF
81
ADF-FEED-MOT(CW)
ON/OFF
82
ADF-FEED-MOT(CCW)
ON/OFF
83
ADF-CLU
ON/OFF
ADF-BELT-MOT(CW)
84
ADF-CLU
ON/OFF
ADF-BELT-MOT(CCW)
85
ADF-FEED-MOT(CCW)
ON/OFF
ADF-BELT-MOT(CW)
ADF-CLU
86
STP-SOL
FLP-SOL
ON/OFF
ADF-CLU
BRKE
*1
*2
*2
Group1
*3
*4
*5
*6
*7
Group2
*1 The feed motor will rotate in the direction appropriate for the cassette loaded at the time of the output signal
check.
*2 For FD2~4-CLT and RGT2~4-CLT,the clutch appro priate for the cassette loaded at the time of the output signal
check will be driven.
*3 The scanning motor will run at the correct speed for the reproduction ratio selected(and displayed)at the time of
the output signal check.
*4 The tray motor moves the tray up when the PRINT key is pressed once,and is turned off when the tray-up switch
is turned on.When the PRINT key is pressed a second time,it moves the tray down and is turned off when the
tray-down switch is turned on.
*5 The length guide motor performs initalisation when the PRINT key is pressed once.When the PRINT key is
pressed a second time, it moves the paper length guide to the widest setting position and then is turned off.When
the PRINT key is pressed a third time,it moves the paper length guide in for a narrow setting and is turned off
when the length guide home switch is turned on.
*6 The width guide motor widens the paper width guide when the PRINT key is pressed once and is turned off when
the width guide home switch is turned on.When the PRINT key is pressed a second time,it narrows the paper
width guide until the A4-R size position and then is turned off.When the PRINT key is pressed a third time,it,widens
the guide until the A3 size position and is turned off.
*7 For TR2 to 4-MOT,the motor appropriate for the cassette loaded at the time of output signal check is chosen.When
the PRINT key is pressed once, the motor moves the tray up and is turned off when TUP2 to 4-SW is turned
on.When the PRINT key is pressed a second time,it moves the tray down and is turned off after a set time lag.
*8 The exposure lamp stays on for 5 sec.and then goes off automatically.
Содержание 65/5560
Страница 61: ...4 5 65 5560 PERIODIC MAY 1997 TOSHIBA CORP Front section view upper unit ...
Страница 62: ...4 6 MAY 1997 TOSHIBA CORP 65 5560 PERIODIC Front section view lower unit 74 75 74 76 75 74 76 75 76 77 77 97 W ...
Страница 63: ...4 7 65 5560 PERIODIC MAY 1997 TOSHIBA CORP Rear side view upper unit ...
Страница 64: ...4 8 MAY 1997 TOSHIBA CORP 65 5560 PERIODIC Rear side view lower unit 80 W 80 W 3 ...
