Toro 78593 Скачать руководство пользователя страница 11

g293529

Figure 17

1.

Shoulder bolt

3.

Belt

2.

Idler pulley

15.

Install the belt onto the clutch. Verify that the
belt is still routed on the blower pulleys and is
seated properly in the pulley grooves.

Note:

You can use a drive ratchet (1/2 inch) to

move the left idler pulley for the blower (

Figure

18

).

g231579

Figure 18

1.

Drive ratchet

2.

Pulley

16.

Raise the blower as described in

Raising the

Blower (page 13)

.

17.

Connect the hydraulic hoses to the
quick-disconnect couplings on the Low Flow
Hydraulics Kit.

WARNING

Hydraulic fluid escaping under pressure
can penetrate skin and cause injury.
Fluid injected into the skin must be
surgically removed within a few hours by
a doctor familiar with this form of injury;
otherwise, gangrene may result.

Ensure that all hydraulic-fluid hoses
and lines are in good condition and all
hydraulic connections and fittings are
tight before applying pressure to the
hydraulic system.

Keep your body and hands away from
pinhole leaks or nozzles that eject
high-pressure hydraulic fluid.

Use cardboard or paper to find
hydraulic leaks; never use your
hands.

11

 

Содержание 78593





















Отзывы: