Toro 74408 Z334 Z Master страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 52

background image

Cleaning

Cleaning Under the Mower

Service Interval:

Before each use or daily

1. Disengage the PTO, move the motion control levers

to the neutral locked position and set the parking
brake.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

3. Raise the mower to the transport position.

4. Lift the front of the machine and support the

machine using jack stands.

Waste Disposal

Engine oil, batteries, hydraulic oil, and engine coolant
are pollutants to the environment. Dispose of these
according to your state and local regulations.

Storage

1. Disengage the power take off (PTO), set the parking

brake, and turn the ignition key to Off. Remove the
key.

2. Remove grass clippings, dirt, and grime from the

external parts of the entire machine, especially the
engine and hydraulic system. Clean dirt and chaff
from the outside of the engine cylinder head fins and
blower housing.

Important:

You can wash the machine with

mild detergent and water. Do not pressure
wash the machine. Avoid excessive use of
water, especially near the control panel, engine,
hydraulic pumps, and motors.

3. Service the air cleaner; refer to Servicing the Air

Cleaner in Engine Maintenance , page 26.

4. Grease the machine; refer to Greasing and

Lubrication in Lubrication , page 22.

5. Change the crankcase oil; refer to Servicing the

Engine Oil in Engine Maintenance , page 26.

6. Check the tire pressure; refer to Checking the Tire

Pressure in Drive System Maintenance , page 33.

7. Change the hydraulic filter; refer to Servicing the

Hydraulic System in Hydraulic System Maintenance ,
page 38.

8. Charge the battery; refer to Servicing the Battery in

Electrical System Maintenance , page 30.

9. Scrape any heavy buildup of grass and dirt from the

underside of the mower, then wash the mower with
a garden hose.

Note:

Run the machine with the PTO engaged

and the engine at high idle for 2 to 5 minutes after
washing.

10. Check the condition of the blades; refer to Servicing

the Cutting Blades in

Mower Deck Maintenance

11. Prepare the machine for storage when non-use

occurs over 30 days. Prepare the machine for storage
as follows:

A. Add a petroleum based stabilizer/conditioner

to fuel in the tank. Follow mixing instructions
from the stabilizer manufacturer. Do not use an
alcohol based stabilizer (ethanol or methanol).

Note:

A fuel stabilizer/conditioner is most

effective when mixed with fresh fuel and used
at all times.

B. Run the engine to distribute conditioned fuel

through the fuel system (5 minutes).

45

«
...
43
44
45
46
47
...
»

Содержание 74408 Z334 Z Master





















































Отзывы:

Нет отзывов

Похожие инструкции для 74408 Z334 Z Master

Бренд: Gardena Страницы: 70

Бренд: Gardena Страницы: 84

Бренд: Gardena Страницы: 24

Бренд: Gardena Страницы: 8

Бренд: Gardena Страницы: 60

Wildcat STWC48V-25CV

Бренд: Scag Power Equipment Страницы: 82

Бренд: White Outdoor Страницы: 4

Бренд: McConnel Страницы: 108

Powermaster 11029S

Бренд: Rover Страницы: 1

ELM 34/1400 PLUS

Бренд: F.F. Group Страницы: 48

GLM 40/124 P EASY

Бренд: F.F. Group Страницы: 128

Бренд: Land Pride Страницы: 2

Бренд: Yard-Man Страницы: 11

Бренд: Yazoo/Kees Страницы: 24

Бренд: AL-KO Страницы: 304

Бренд: Sabo Страницы: 280

Бренд: Gardenline Страницы: 17

Бренд: MTD Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды