Toro 74408 Z334 Z Master страница 46 Скачать руководство пользователя

Страница: 46 / 52

C. Stop the engine, allow it to cool, and drain the

fuel tank; refer to Servicing the Fuel Tank in Fuel
System Maintenance , page 29.

D. Restart the engine and run it until it stops.

E. Dispose of fuel properly. Recycle as per local

codes.

Important:

Do not store

stabilizer/conditioned fuel over 90 days.

12. Check and tighten all bolts, nuts, and screws. Repair

or replace any part that is damaged.

13. Paint all scratched or bare metal surfaces. Paint is

available from your Authorized Service Dealer.

14. Store the machine in a clean, dry garage or storage

area. Remove the key from the ignition switch and
keep it out of reach of children or other unauthorized
users. Cover the machine to protect it and keep it
clean.

Содержание 74408 Z334 Z Master





















































Результаты поиска

Содержание 74408 Z334 Z Master

Отзывы:

Похожие инструкции для 74408 Z334 Z Master

Бренды по названию

Популярные бренды

Toro 74408 Z334 Z Master, Руководство оператора

Результаты поиска

Содержание 74408 Z334 Z Master

Отзывы:

Похожие инструкции для 74408 Z334 Z Master

Бренды по названию

Популярные бренды