Toro 74408 Z334 Z Master страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 52

background image

Charging the Battery

Charging the battery produces gasses that can
explode.

Never smoke near the battery and keep sparks
and flames away from battery.

Important:

Always keep the battery fully charged

(1.265 specific gravity). This is especially important
to prevent battery damage when the temperature is
below 32°F (0°C).

1. Charge battery for 10 to 15 minutes at 25 to 30 amps

or 30 minutes at 4-6 amps.

2. When the battery is fully charged, unplug the charger

from the electrical outlet, then disconnect the
charger leads from the battery posts (Figure 37).

Figure 37

3. Install the battery in the machine and connect the

battery cables; refer to Installing the Battery.

Note:

Do not run the machine with the battery

disconnected, electrical damage may occur.

Servicing the Fuses

The electrical system is protected by fuses. It requires
no maintenance, however, if a fuse blows check
component/circuit for malfunction or short.

Fuse:

•

Main, F1-20 amp, blade-type

•

Charge circuit, F2-20 amp, blade-type

1. Raise the seat to gain access to the fuses on the left

side of the machine (Figure 38).

2. To replace the fuses, pull out on the fuse to remove

it.

3. Install a new fuse (Figure 38).

Figure 38

1.

Fuse location

3.

Charge circuit, 20 amp

2.

Main, 20 amp

32

«
...
30
31
32
33
34
...
»

Содержание 74408 Z334 Z Master





















































Отзывы:

Нет отзывов

Похожие инструкции для 74408 Z334 Z Master

Бренд: Salsco Страницы: 29

Бренд: Yard force Страницы: 16

Greens King IV 62287

Бренд: Jacobsen Страницы: 138

Бренд: Yard-Man Страницы: 11

Бренд: Lastec Страницы: 68

Бренд: F.F. Group Страницы: 52

Бренд: Poulan Pro Страницы: 28

Бренд: Weed Eater Страницы: 13

26" Leaf/Lawnsweeper 45-02181

Бренд: Agri-Fab Страницы: 12

Бренд: Bestgreen Страницы: 10

Бренд: Lux Tools Страницы: 148

Бренд: Poulan Pro Страницы: 17

Бренд: Parkside Страницы: 52

Бренд: Bushranger Страницы: 20

Бренд: VITO GARDEN Страницы: 33

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды