Toro 74408 Z334 Z Master страница 48 Скачать руководство пользователя

Страница: 48 / 52

Problem

Possible Cause

Corrective Action

1. Blade(s) not sharp.

1. Sharpen the blade(s).

2. Cutting blade(s) is/are bent.

2. Install new cutting blade(s).

3. Mower is not level.

3. Level the mower from side-to-side and

front-to-rear.

4. Underside of mower is dirty.

4. Clean the underside of the mower.

5. Tire pressure is not correct.

5. Adjust the tire pressure.

Uneven cutting height.

6. Blade spindle bent.

6. Contact an Authorized Service Dealer.

1. Drive belt is worn, loose or broken.

1. Check the belt tension.

2. Drive belt is off pulley.

2. Install the drive belt and check

adjusting shafts and belt guides for
correct position.

3. Deck belt is worn, loose or broken.

3. Install a new deck belt.

4. Deck belt is off pulley.

4. Install the deck pulley and check the

idler pulley, idler arm and spring for
correct position and function.

Blades do not rotate.

5. Broken or missing idler spring.

5. Replace the spring.

Содержание 74408 Z334 Z Master





















































Результаты поиска

Содержание 74408 Z334 Z Master

Отзывы:

Похожие инструкции для 74408 Z334 Z Master

Бренды по названию

Популярные бренды

Toro 74408 Z334 Z Master, Руководство оператора

Результаты поиска

Содержание 74408 Z334 Z Master

Отзывы:

Похожие инструкции для 74408 Z334 Z Master

Бренды по названию

Популярные бренды