Toro 74408 Z334 Z Master страница 31 Скачать руководство пользователя

Страница: 31 / 52

Incorrect battery cable routing could damage
the machine and cables causing sparks. Sparks
can cause the battery gasses to explode,
resulting in personal injury.

•

Always Disconnect the negative (black)
battery cable before disconnecting the
positive (red) cable.

•

Always Reconnect the positive (red) battery
cable before reconnecting the negative
(black) cable.

1. Disengage the PTO, move the motion control levers

to the neutral locked position, and set the parking
brake.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

3. Unlatch the seat and tilt the seat up.

4. First disconnect the negative battery cable and

ground wire from the negative (-) battery terminal
(Figure 36).

5. Slide the red terminal boot off the positive (red)

battery terminal. Then remove the positive (red)
battery cable (Figure 36).

Figure 36

Battery

J-bolts

Positive battery post

Bolt (1/4 x 3/4 inch)

Negative battery post

Ground wire

Terminal boot

10.

Negative battery cable

Battery clamp

11.

Locknut (1/4 inch)

Wingnut (1/4 inch)

12.

Positive battery cable

6. Remove both wing nuts (1/4 inch) securing the

battery clamp (Figure 36).

7. Remove the battery.

Installing the Battery

1. Position battery in the tray with the terminal posts

toward the engine (Figure 36).

2. First, install the positive (red) battery cable to

positive (+) battery terminal.

3. Then install the negative battery cable and ground

wire to the negative (-) battery terminal.

4. Secure the cables with 2 bolts (1/4 x 3/4 inch),

2 washers (1/4 inch), and 2 locknuts (1/4 inch)
(Figure 36).

5. Slide the red terminal boot onto the positive (red)

battery post.

6. Secure battery with J-bolts, hold down clamp and

2 washers (1/4 inch), and 2 wing nuts (1/4 inch)
(Figure 36).

Содержание 74408 Z334 Z Master





















































Результаты поиска

Содержание 74408 Z334 Z Master

Отзывы:

Похожие инструкции для 74408 Z334 Z Master

Бренды по названию

Популярные бренды

Toro 74408 Z334 Z Master, Руководство оператора

Результаты поиска

Содержание 74408 Z334 Z Master

Отзывы:

Похожие инструкции для 74408 Z334 Z Master

Бренды по названию

Популярные бренды