Toro 74408 Z334 Z Master страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 52

background image

Hydraulic System
Maintenance

Servicing the Hydraulic
System

Checking the Hydraulic Fluid

Service Interval:

After the first 8 hours

Every 50 hours

Fluid Type: Mobil 1 15W-50 synthetic motor oil or
equivalent synthetic oil.

Important:

Use oil specified or equivalent. Other

fluids could cause system damage.

Note:

There are two ways of checking the hydraulic

oil; when the oil is warm or when the oil is cold. The
tank has two levels depending if the oil is warm or cold
(Figure 49).

1. Position the machine on a level surface and set the

parking brake.

2. Clean the area around the hydraulic tank (Figure 49).

3. If the machine has not been started and is cold,

ensure the fluid is up to the cold line on the side of
the hydraulic tank.

4. If the machine has been run and is up to normal

operating temperature, ensure the fluid is up to the
hot line on the side of the hydraulic tank.

5. If fluid is needed, remove the cap from the filler

neck (Figure 49).

6. Add fluid to the reservoir until it reaches the cold or

hot line of the tank depending on the temperature
of the fluid.

7. Install the cap on filler neck.

Figure 49

1.

Cap

3.

Cold fluid level-full

2.

Baffle

4.

Hot fluid level-full

Hydraulic fluid escaping under pressure can
penetrate skin and cause injury.

•

If hydraulic fluid is injected into the skin
it must be surgically removed within a few
hours by a doctor familiar with this type of
injury. Gangrene may result if this is not
done.

•

Keep body and hands away from pin hole
leaks or nozzles that eject high pressure
hydraulic fluid.

•

Use cardboard or paper to find hydraulic
leaks.

•

Safely relieve all pressure in the hydraulic
system before performing any work on the
hydraulic system.

•

Make sure all hydraulic fluid hoses and
lines are in good condition and all hydraulic
connections and fittings are tight before
applying pressure to hydraulic system.

Replacing the Hydraulic Filters and Oil

Service Interval:

After the first 250 hours

Yearly—Change the hydraulic filters
and oil.

38

«
...
36
37
38
39
40
...
»

Содержание 74408 Z334 Z Master





















































Отзывы:

Нет отзывов

Похожие инструкции для 74408 Z334 Z Master

532 43 45-09 Rev. 1

Бренд: McCulloch Страницы: 76

FREEDOM Z SFZ36-17KA

Бренд: Scag Power Equipment Страницы: 69

Бренд: MTD Страницы: 37

Бренд: Yard-Man Страницы: 24

Zero Turn Rotary Mower

Бренд: Jacobsen Страницы: 62

APACHE 1275 ZSL

Бренд: Garland Страницы: 184

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 16

6Speed - 96012008900 42" 16.5HP Riding Mower

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 8

Бренд: Electrolux Страницы: 10

Бренд: Electrolux Страницы: 40

Bestgreen BM135H107

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 76

Бренд: Electrolux Страницы: 56

Бренд: Electrolux Страницы: 88

Flymo Compact 300

Бренд: Electrolux Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды