Toro 74408 Z334 Z Master Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 52

background image

Maintenance

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 8 hours

• Check for any loose fasteners and tighten them.
• Change the engine oil.
• Tighten the wheel lug nuts.
• Check the hydraulic fluid.

After the first 250 hours

• Change the hydraulic filters and oil.

Before each use or daily

• Check the safety system.
• Check the engine oil level.
• Clean the air intake screen.
• Check the brake.
• Check the mower blades.
• Clean the mower deck.

Every 25 hours

• Clean foam air cleaner element. (more often in dirty or dusty conditions)

Every 50 hours

• Check the paper air cleaner element. (more often in dirty or dusty conditions)
• Check the tire pressure.
• Check pump drive belt.
• Check the hydraulic fluid.

Every 100 hours

• Change the engine oil. (more often in dirty or dusty conditions)
• Check the spark plugs.
• Check and clean engine cooling fins and shrouds.
• Inspect all belts for cracks and wear.

Every 150 hours

• Lubricate the machine with light oil

Every 200 hours

• Replace the paper air cleaner element.
• Replace the oil filter
• Replace the fuel filter.

Every 500 hours

• Adjust the caster pivot bearing.

Yearly

• Grease the front caster pivots (more often in dirty or dusty conditions)
• Lubricate the caster wheel hubs.
• Change the hydraulic filters and oil.

Important:

Refer to your

Engine Operator’s Manual

for additional maintenance procedures.

If you leave the key in the ignition switch, someone could accidently start the engine and seriously
injure you or other bystanders.

Remove the key from the ignition and disconnect the wire from the spark plug(s) before you do any
maintenance. Set the wire aside so that it does not accidentally contact the spark plug.

Lubrication

Greasing and Lubrication

Lubricate the machine when shown on the Check
Service Reference Aid decal (Figure 21). Grease more

frequently when operating conditions are extremely
dusty or sandy.

Grease Type: General-purpose grease.

22

«
...
20
21
22
23
24
...
»

Содержание 74408 Z334 Z Master





















































Отзывы:

Нет отзывов

Похожие инструкции для 74408 Z334 Z Master

Бренд: Toro Страницы: 48

Бренд: Yard-Man Страницы: 44

Бренд: Yard force Страницы: 25

Бренд: HUSTLER Страницы: 65

Бренд: Gude Страницы: 108

Бренд: Weed Eater Страницы: 13

Бренд: MTD Страницы: 35

TH910 Series II

Бренд: Deutscher Страницы: 22

Бренд: Einhell Royal Страницы: 24

Бренд: Toro Страницы: 48

Бренд: VonHaus Страницы: 20

PERFORMANCE 50562X89

Бренд: YARD KING Страницы: 60

Бренд: Electrolux Страницы: 44

Flymo Roller Compact 400

Бренд: Electrolux Страницы: 15

Бренд: Electrolux Страницы: 14

Бренд: Electrolux Страницы: 13

Бренд: Black & Decker Страницы: 4

Бренд: Black & Decker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды