Toro 30339 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 52

background image

49

Cleaning and Storage

1. Disengage the power take off (PTO) and turn the

ignition key to “OFF” to stop the engine. Remove the
key.

2. Remove grass clippings, dirt, and grime from the

external parts of the entire machine, especially the
engine. Clean dirt and chaff from the outside of the
engine’s cylinder head fins and blower housing.

Important

You can wash the machine with mild

detergent and water. Do not pressure wash the machine.
Avoid excessive use of water, especially near the control
panel, engine, hydraulic pumps and motors.

3. Service the air cleaner; refer to Air Cleaner Service,

page 25.

4. Change the crankcase oil; refer to Engine Oil Service,

page 26.

5. Change the hydraulic filter; refer to Hydraulic System

Service on page 31.

6. Check the tire pressure; refer to Checking Tire

Pressure, page 29.

7. For storage over 30 days, prepare the traction unit as

follows.

A. Add a petroleum based stabilizer/conditioner to

fuel in the tank. Follow mixing instructions from
stabilizer manufacturer. Do not use an alcohol
based stabilizer (ethanol or methanol).

Note: A fuel stabilizer/conditioner is most effective when
mixed with fresh gasoline and used at all times.

B. Run the engine to distribute conditioned fuel

through the fuel system (5 minutes).

C. Stop the engine, allow it to cool and drain the fuel

tank; refer to Draining Fuel Tank, page 30.

D. Restart the engine and run it until it stops.

E. Choke or prime the engine.

F. Start and run the engine until it will not start again.

Use the primer, if equipped on machine, several
times to ensure no fuel remains in primer system.

G. Dispose of fuel properly. Recycle as per local

codes.

Important

Do not store stabilizer/conditioned gasoline

over 90 days.

8. Remove the spark plug(s) and check its condition;

refer to Spark Plug Service on page 27. With the spark
plug(s) removed from the engine, pour two
tablespoons of engine oil into the spark plug hole.
Now use the starter to crank the engine and distribute
the oil inside the cylinder. Install the spark plug(s). Do
not install the wire on the spark plug(s).

9. Check and tighten all bolts, nuts, and screws. Repair or

replace any part that is damaged or defective.

10. Paint all scratched or bare metal surfaces. Paint is

available from your Authorized Service Dealer.

11. Store the machine in a clean, dry garage or storage

area. Remove the key from the ignition switch and
keep it in a memorable place. Cover the machine to
protect it and keep it clean.

Troubleshooting

PROBLEM

POSSIBLE CAUSES

CORRECTIVE ACTION

Engine will not start, starts hard, or

1.

Fuel tank is empty.

1.

Fill fuel tank with gasoline.

g

,

,

fails to keep running.

2.

PTO is on (Pulled up).

2.

Turn PTO off (Push in).

3.

Speed control lever is in gear.

3.

Move speed control lever to
neutral.

4.

Choke is not ON.

4.

Move choke lever to ON.

5.

Air cleaner is dirty.

5.

Clean or replace air cleaner
element.

6.

Spark plug wire is loose or
disconnected.

6.

Install wire on spark plug.

7.

Spark plug is pitted, fouled, or
gap is incorrect.

7.

Install new, correctly gapped
spark plug.

8.

Dirt in fuel filter.

8.

Replace fuel filter.

9.

Dirt, water, or stale fuel is in
fuel system.

9.

Contact Authorized Service
Dealer.

«
...
47
48
49
50
51
...
»

Содержание 30339





















































Отзывы:

Нет отзывов

Похожие инструкции для 30339

Бренд: Lastec Страницы: 69

Бренд: Racing Страницы: 17

Бренд: Scag Power Equipment Страницы: 24

HydroCut 5900604

Бренд: Ferris Страницы: 54

Agco Allis 1692173

Бренд: Simplicity Страницы: 60

Бренд: Simplicity Страницы: 11

Бренд: Ryobi Страницы: 36

Бренд: Snapper Страницы: 224

Бренд: Toro Страницы: 44

Бренд: Eliet Страницы: 106

Бренд: Honda Страницы: 21

Бренд: Weed Eater Страницы: 48

Бренд: Toyama Страницы: 60

Бренд: Ego Power+ Страницы: 16

Бренд: Ego Power+ Страницы: 224

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 23

Бренд: Craftsman Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды