Toro 30339 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 52

background image

27

1

2

3

Figure 21

1.

Oil dipstick

2.

Metal end

3.

Filler tube

Changing/Draining Oil

1. Start the engine and let it run five minutes. This warms

the oil so it drains better.

2. Park the machine so that the drain side is slightly

lower than the opposite side to make sure the oil drains
completely. Then disengage the power take off (PTO),
set the parking brake, and turn the ignition key to
“OFF” to stop the engine. Remove the key.

3. Place a pan below the oil drain. Remove the oil drain

cap (Fig. 22).

4. When oil has drained completely, install the oil drain

cap.

Note: Dispose of the used oil at a certified recycling
center.

1

m–5207

Figure 22

1.

Oil drain cap

5. Slowly pour approximately 80% of the specified oil,

page 26, into the filler tube (Fig. 21). Now check the
oil level; refer to Checking Oil Level, page 26. Slowly
add additional oil to bring to “FULL” mark on
dipstick.

Change Oil Filter

Service Interval/Specification

Replace the oil filter every 200 hours or every other oil
change.

Note: Change oil filter more frequently when operating
conditions are extremely dusty or sandy.

1. Drain the oil from the engine; refer to

Changing/Draining Oil, page 27.

2. Remove the old filter (Fig. 23).

3. Apply a thin coat of new oil to the rubber gasket on

the replacement filter (Fig. 23).

1

2

M-

Figure 23

1.

Oil filter

2.

Adapter

4. Install the replacement oil filter to the filter adapter.

Turn the oil filter clockwise until the rubber gasket
contacts the filter adapter, then tighten the filter an
additional 3/4 turn (Fig. 23).

5. Fill the crankcase with the proper type of new oil;

refer to Engine Oil Service, page 26.

Spark Plug Service

Service Interval/Specification

Check the spark plug(s) after every 100 operating hours.
Make sure the air gap between the center and side
electrodes is correct before installing the spark plug. Use a
spark plug wrench for removing and installing the spark
plug(s) and a gapping tool/feeler gauge to check and
adjust the air gap. Install a new spark plug(s) if necessary.

«
...
25
26
27
28
29
...
»

Содержание 30339





















































Отзывы:

Нет отзывов

Похожие инструкции для 30339

Бренд: Toro Страницы: 52

Бренд: Texas Страницы: 16

Бренд: Parklander Страницы: 42

Бренд: GARDEO PRO Страницы: 100

Бренд: Yazoo/Kees Страницы: 42

Бренд: Etesia Страницы: 42

Бренд: MTD Страницы: 29

Бренд: Flymo Страницы: 10

Бренд: MTD Страницы: 28

Бренд: Gtech Страницы: 32

Бренд: Toro Страницы: 48

Бренд: Simplicity Страницы: 56

Бренд: Kubota Страницы: 315

Бренд: Husqvarna Страницы: 56

Бренд: Husqvarna Страницы: 65

Бренд: Husqvarna Страницы: 64

Бренд: Husqvarna Страницы: 55

Бренд: Husqvarna Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды