Toro 30339 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

background image

30

2

1

m–2147

Figure 29

1.

Rear Tire

2.

Caster tire

Fuel Tank Service

Danger

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and others
and can damage property.

•

Drain gasoline from the fuel tank when the
engine is cold. Do this outdoors in an open area.
Wipe up any gasoline that spills.

•

Never smoke when draining gasoline, and stay
away from an open flame or where a spark may
ignite the gasoline fumes.

Draining The Fuel Tank

1. Park the machine on a level surface, to assure fuel tank

drains completely. Then disengage the power take off
(PTO), set the parking brake, and turn the ignition key
to “OFF” to stop the engine. Remove the key.

2. Close fuel shut–off valve at fuel tank (Fig. 30).

Note: Remove fuel line from fuel valve that is closest to
the engine.

3. Squeeze the ends of the hose clamp together and slide

it up the fuel line away from valve (Fig. 30).

4. Pull the fuel line off the valve (Fig. 30). Open fuel

shut-off valve and allow gasoline to drain into a gas
can or drain pan.

Note: Now is the best time to install a new fuel filter
because the fuel tank is empty. Refer to Replacing the
Fuel Filter; page 30.

5. Install the fuel line onto the valve. Slide the hose

clamp close to the valve to secure the fuel line.

1

2

m–5185

Figure 30

1.

Fuel shut-off valve

2.

Clamp

Fuel Filter Service

Service Interval/Specification

Replace the fuel filter after every 200 operating hours or
yearly, whichever occurs first.

Replacing the Fuel Filter

Never install a dirty filter if it is removed from the fuel
line.

Note: Note how the fuel filter is installed.

1. Disengage the power take off (PTO), set the parking

brake, and turn the ignition key to “OFF” to stop the
engine. Remove the key.

2. Close fuel shut–off valve at fuel tank (Fig. 30).

3. Squeeze the ends of the hose clamps together and slide

them away from the filter (Fig. 31).

4. Remove the filter from the fuel lines.

5. Install a new filter and move the hose clamps close to

the filter.

6. Open fuel shut-off valve at fuel tank (Fig. 30).

«
...
28
29
30
31
32
...
»

Содержание 30339





















































Отзывы:

Нет отзывов

Похожие инструкции для 30339

Бренд: McCulloch Страницы: 36

Бренд: MK Martin Страницы: 30

Бренд: MacAllister Страницы: 18

Бренд: Parkside Страницы: 160

Бренд: Yard-Man Страницы: 24

Бренд: McCulloch Страницы: 44

Бренд: FLORABEST Страницы: 44

Бренд: Scag Power Equipment Страницы: 41

Бренд: AMBROGIO Страницы: 30

Бренд: Scag Power Equipment Страницы: 96

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды