Toro 30339 Скачать руководство пользователя страница 35

Страница: 35 / 52

6. If the wheel turns while holding the drive lever in

neutral, the neutral control linkages need to be
adjusted (Fig. 38). If wheel stops then go to step 12.

7. Loosen the nut against the neutral control linkage yoke

(Fig. 38).

8. Adjust the neutral control linkage until the respective

drive wheel stops while the drive lever is pulled
against the neutral spring (neutral position) (Fig. 38).

9. Turn the adjusting bolt approximately 1/4 turn

clockwise if the wheel is turning in reverse or turn the
bolt approximately 1/4 turn counter–clockwise if the
wheel is turning forward (Fig. 38).

10. Release the drive lever to the forward drive position

and squeeze back into the neutral position. Check to
see if the wheel stops. If not, repeat the above
adjustment procedure.

11. After adjustments are made, tighten the nuts against

the yokes.

12. Repeat this procedure for the opposite side.

m–5394

Figure 38

Neutral control linkage

Yoke

Adjusting bolt

Nut

Adjust Hydro Control Linkages

Engine must be running so control linkage
adjustments can be performed. Contact with
moving parts or hot surfaces may cause personal
injury.

Keep hands, feet, face, clothing and other body
parts away from rotating parts, muffler and other
hot surfaces.

Warning

Mechanical or hydraulic jacks may fail to support
machine and cause a serious injury.

•

Use jack stand when supporting machine.

•

Do not use hydraulic jacks.

Warning

Left Side Linkage Adjustment

1. Raise the rear of the machine onto jack stands high

enough to raise the drive wheels off of the ground.

2. Place the speed control lever in the neutral position.

3. Place the left drive lever in the full forward position.

4. Hold OPC levers down.

Note: The OPC levers must be held down whenever the
speed control lever is out of the neutral position or the
engine will kill.

Electrical system will not perform proper safety
shut off with Operator Presence Control (OPC)
levers held in place.

•

Make sure Operator Presence Control (OPC)
levers are working when adjustment is
completed.

•

Never operate this unit with Operator Presence
Control (OPC) levers held in place.

Warning

5. Loosen the front nut on left hydro control linkage as

shown in figure 39.

6. Turn the left rear adjusting nut counter–clockwise until

wheel rotates forward (Fig. 39).

7. Turn the rear adjusting nut clockwise 1/4 of a turn at a

time. Then move the speed control lever forward and
back to neutral. Repeat this until left wheel stops
rotating forward (Fig. 39).

8. Turn the rear nut an additional 1/2 turn and tighten the

front nut.

Note: Make sure flat part of linkage is perpendicular to
pin part of swivel.

9. After adjusting the left hydro control linkage, move

the speed control lever forward and then back to the
neutral position.

10. Make sure the speed control lever is in the neutral

position and the tire does not rotate.

11. Repeat adjustment if needed.

Содержание 30339





















































Результаты поиска

Содержание 30339

Отзывы:

Похожие инструкции для 30339

Бренды по названию

Популярные бренды

Toro 30339, Руководство оператора

Результаты поиска

Содержание 30339

Отзывы:

Похожие инструкции для 30339

Бренды по названию

Популярные бренды