Toro 30339 Скачать руководство пользователя страница 36

Страница: 36 / 52

m–5394

Figure 39

Hydro control linkage

Front nut

Rear adjusting nut

Note: If inconsistent neutral occurs, check to be sure both
springs are properly tightened on the speed control lever
under the console, especially the rear pivot spring. Repeat
above adjustments if necessary (Fig. 40).

m–5396

Figure 40

Speed control lever

Rear pivot spring

spring

Right Side Linkage Adjustment

1. Place the speed control lever in the neutral position.

2. Place the right drive lever in the full forward position.

3. Hold OPC levers down.

Note: The OPC levers must be held down whenever the
speed control lever is out of the neutral position or the
engine will kill.

4. Adjust the right side linkage by turning the quick track

knob counterclockwise until the tire begins to rotate
forward (Fig. 41).

5. Turn the knob clockwise 1/4 of a turn at a time. Then

move the speed control forward and back to neutral.
Repeat this until right wheel stops rotating forward
(Fig. 41).

6. The spring that keeps tension on the knob should

normally not need adjustment. However if adjustment
is needed, adjust the length of spring to 1 in. (26 mm)
between the washers (Fig. 41).

7. Adjust spring length by turning nut at front of spring

(Fig. 41).

m–5403

Figure 41

Hydro control linkage

Quick track knob

Spring

1 inch (26 mm)

Control Rod Adjustment

Checking Control Rod

1. With rear of machine still on jack stands and engine

running at full throttle, move the speed control lever to
the medium speed position.

Note: The OPC levers must be held down whenever the
speed control lever is out of the neutral position or the
engine will kill.

2. Move the respective drive lever upward until it reaches

the neutral position and engage neutral locks.

3. If the tire rotates in either direction, the length of the

control rod will need to be adjusted.

Adjusting Control Rods

1. Adjust the rod length by releasing the drive lever and

removing clevis pin. Rotate the rod in the rod fitting
(Fig. 42).

Содержание 30339





















































Результаты поиска

Содержание 30339

Отзывы:

Похожие инструкции для 30339

Бренды по названию

Популярные бренды

Toro 30339, Руководство оператора

Результаты поиска

Содержание 30339

Отзывы:

Похожие инструкции для 30339

Бренды по названию

Популярные бренды