Toro 30339 Скачать руководство пользователя страница 34

Страница: 34 / 52

m–5398

Figure 36

Speed control rod

Yoke

Speed control crank

Tabs, 6 o’clock position

Jam nut

5. Pull the speed control lever back to neutral.

6. Check to make sure the safety switch is depressed and

there is a 5/16 in. (8 mm) space between the actuating
tab and the switch. (Fig. 37).

7. If needed, adjust switch location to create the 5/16 in.

(8 mm) space (Fig. 37).

m–5394

Figure 37

Actuating tab

5/16 in. (8 mm) space

Safety switch

Adjust Neutral Control
Linkages

Engine must be running so control linkage
adjustments can be performed. Contact with
moving parts or hot surfaces may cause personal
injury.

Keep hands, feet, face, clothing and other body
parts away from rotating parts, muffler and other
hot surfaces.

Warning

Mechanical or hydraulic jacks may fail to support
machine and cause a serious injury.

•

Use jack stand when supporting machine.

•

Do not use hydraulic jacks.

Warning

1. Raise the rear of the machine onto jack stands to raise

the drive wheels off the ground.

2. Start the engine and move the throttle ahead to the full

throttle position.

3. Place the neutral locks in the full forward position and

move the speed control lever to the medium speed
position.

4. Hold OPC levers down.

Note: The OPC levers must be held down whenever the
speed control lever is out of the neutral position or the
engine will kill.

Electrical system will not perform proper safety
shut off with Operator Presence Control (OPC)
levers held in place.

•

Make sure Operator Presence Control (OPC)
levers are working when adjustment is
completed.

•

Never operate this unit with Operator Presence
Control (OPC) levers held in place.

Warning

5. Squeeze one drive lever until an increased resistance is

felt. This is where neutral should be.

Note: Make sure you have not reached the end of the
neutral lock slot. If you have, shorten the control lever
linkage. Refer to Control Rod Adjustment on page 36.

Содержание 30339





















































Результаты поиска

Содержание 30339

Отзывы:

Похожие инструкции для 30339

Бренды по названию

Популярные бренды

Toro 30339, Руководство оператора

Результаты поиска

Содержание 30339

Отзывы:

Похожие инструкции для 30339

Бренды по названию

Популярные бренды