Toro 08839 Скачать руководство пользователя

Страница: 9 / 64

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

Mid-mount attachment (ordered
separately; refer to your authorized Toro
distributor)

Install a mid-mount attachment.

No parts required

–

Prepare the machine.

Short drawbar chain (17-1/2 inches)

Lift bracket

Carriage bolt (5/16 x 1 inch)

Washer (3/8 x 7/8 inch)

Flange locknut (5/16 inch)

Rear attachment lift frame assembly

Long rear-lift chain (25 inches)

Shackle

Clevis pin

Cotter pin

Flange-head bolt (3/8 x 1-3/4 inches)

Washer (2/5 inch)

Flange locknut (3/8 inch)

Chain sleeve

Flange-head bolt (1/2 x 3 inches)

Flange locknut (1/2 inch)

Capscrew (3/4 x 4-1/2 inches)

Locknut (3/4 inch)

Flange-head bolt (3/8 x 1-1/2 inches)

Assemble the rear attachment lift frame.

Installing a Mid-Mount Attachment

Parts needed for this procedure:

Mid-mount attachment (ordered separately; refer to your authorized Toro distributor)

Procedure

Install a Toro-approved mid-mount attachment; refer to the mid-mount attachment

Installation Instructions

Содержание 08839

































































Результаты поиска

Содержание 08839

Отзывы:

Похожие инструкции для 08839

Бренды по названию

Популярные бренды

Toro 08839, Руководство оператора

Результаты поиска

Содержание 08839

Отзывы:

Похожие инструкции для 08839

Бренды по названию

Популярные бренды