manualshive.com logo in svg

Toro 08839, Руководство оператора

Поделиться
Скачать
Toro 08839 Скачать руководство пользователя страница 7

decal106-5517

106-5517

1.

Warning—do not touch the hot surface.

decal115-4855

115-4855

1.

Hot surface/burn hazard—wear protective gloves when
handling the hydraulic couplers and read the

Operator's

Manual

for information on handling hydraulic components.

decal116-5610

116-5610

1.

Hour meter

4.

Neutral

2.

Power take-off (PTO)

5.

Operator presence switch

3.

Parking brake

6.

Battery

decal137-9505

137-9505

1.

Do not use fuel with an alcohol content by volume greater
than 10%.

decal132-1316

132-1316

1.

Entanglement hazard, belt—keep away from moving parts.

decal133-8062

133-8062

decal138-4107

138-4107

1.

Crushing hazard of the hand—keep hands away from the
pinch point.

decal125-8483

125-8483

1.

Hydraulic fluid; read the

Operator’s Manual

.

decal120-9570

120-9570

1.

Warning—stay away from moving parts, keep all guards
and shields in place.

7

 

Содержание 08839

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды