Tornatech HFD Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 48

Tornatech HFD Скачать руководство пользователя страница 42

42

How to Test:

Charger 1 Fail

Unpower the charger 1 by putting the circuit breaker in the off position.

Charger 2 Fail

Unpower the charger 2 by putting the circuit breaker in the off position.

DC Failure

Switch Circuit Breaker 3 (CB3) and Circuit Breaker 4 (CB4) in Off position or disconnect #6 and #8 engine wires
(See drawing for more details).

Controller Trouble

To activate this common alarm, at least one of the following alarms must be active: Charger Failure 1, Charger
Failure 2, DC Failure, Faulty Pressure Transducer or Weekly Test Check Solenoid Valve.

Low Fuel Level

Disconnect Fuel Level connector. Depending of your sensor type, put a jumper between positive pin (left) or negative
pin (right) and signal pin (middle) of this connector (See drawing for more details).

High Fuel Level

Disconnect Fuel Level connector. Depending of your sensor type, put a jumper between positive pin (left) or negative
pin (right) and signal pin (middle) of this connector (See drawing for more details).

Fuel Tank Leak

Put a jumper between Fuel Tank Leak input and ground (See drawing for more details).

AC Failure

Make sure both batteries are connected and all circuit breakers are in On position. Switch Circuit Breaker 1 (CB1)
and Circuit Breaker (CB2) in Off position. Disconnect J44 from the I/O board.

Water Reservoir Empty

Put a jumper between Water Reservoir Empty input and ground (See drawing for more details).

High Water Level

Disconnect Water Level connector. Depending of your sensor type, put a jumper between positive pin (left) or
negative pin (right) and signal pin (middle) of this connector (See drawing for more details).

Water Reservoir Low

Disconnect Water Level connector. Depending of your sensor type, put a jumper between positive pin (left) or
negative pin (right) and signal pin (middle) of this connector (See drawing for more details).

Pump Room Alarm

To activate this common alarm, at least one of the following alarms must be active: Low Fuel Level, High Fuel Level,
Fuel Tank Leak, AC Fail, Low Ambient Temperature, High Ambient Temperature, Low Suction Pressure, Water
Reservoir Empty, High Water Level or Water Reservoir Low.

Fail to Start

Disconnect #1, #9, #10 and #12 engine wires (See drawing for more details). Start the cranking sequence (Example:
Remove Remote Automatic Start jumper). Wait until the cranking sequence ends.

Technical Documents

«
...
40
41
42
43
44
...
»

Содержание HFD

















































Отзывы:

Нет отзывов