manualshive.com logo in svg

Tornatech HFD, Руководство по установке и обслуживанию, Страница: 26 / 48

Поделиться
Скачать
Tornatech HFD Скачать руководство пользователя страница 26

 

 

26 

 

Voltage Coast Drop Detection Enable : If enable, this second condition on the battery test is activated. On smaller 
battery, the rise in current during a boost test might be to small to have a conclusive test. This second test verify the 
capacitive effect on the battery line after a boost sequence. 
 
Battery Fail From Engine RPM During Crank : If enable, the Battery Fail alarm will be activated if no RPM is read 
after a crank cycle  
 
Charger 1-2 Power Supply Voltage Reference : This is the voltage that is applied by the battery charger in power 
supply mode (no battery connected). To measure this voltage, the battery must be disconnected. 
 

Timers Page 

Config > Advanced > Timers1-2 

 

 

Most common timers for fire pump control can be configured here. Note that any timer set to 0 will remove the delay 
in the decision process. 
 
Access level 1: 
 
- Engine starting and stopping:  
The “Sequential Start Timer” allows a delayed response on an automatic start request.  
- Energize to Stop: 
This timer set the time in second the fuel solenoide valve will close after a stop.  
- Fail When Running Timer: 

Содержание HFD

















































Отзывы:

Нет отзывов