manualshive.com logo in svg

Tornatech HFD, Руководство по установке и обслуживанию, Страница: 15 / 48

Поделиться
Скачать
Tornatech HFD Скачать руководство пользователя страница 15

 

 

15 

 

Warning 
After 2 years of service, the Vizitouch battery may become less efficient and could lose the time after a shutdown. 
 

Alarm Bell 

The alarm bell is activated under  default faulty conditions and under optional or user defined conditions. 
Any of these conditions will energize the alarm bell but may be silenced, by pressing on the “Alarms / Silence” 
membrane button. When silenced, the alarm bell restarts ringing if a new fault occurs or if the alarm conditions 
remain unchanged after 24 hours. The alarm bell automatically stops ringing if alarm conditions are not present 
anymore. 
Note: other external conditions may trigger optional conditions depending of the factory settings. Verify drawings 
affixed inside the cabinet. 
 
Default Conditions : 
- Engine Overspeed 
- Engine Low Oil Pressure 
- Engine High Coolant Temperature 
- Engine Fail to Start 
- Battery Failure 1-2 
- DC Failure 
- AC Fail 
- I/O Cards Communication Loss 
- CAN System Failure 
- File System Failure 
 

First Setup 

The First Setup must be done prior to using the controller. Completing the First Setup is the only way to access the 
homepage and enable the automatic mode of the controller. 

 

 

Содержание HFD

















































Отзывы:

Нет отзывов