Tornatech HFD Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 48

Tornatech HFD Скачать руководство пользователя страница 27

27

If Enabled, this timer will delay the "Fail When Running Alarm".
- Local Request Detection:
This is the delay it will take to the controller to detect a Local start of the pump.

The other timers are self explanatory and set the time delay on alarms.

Inputs/Outputs Configuration

Config > Advanced > IO Diesel Input Selection -

Config - Output Config

This page, if logged in, allows the re-assignation of 3 programmable inputs by pressing on the signal name. If the
Deluge Valve signal is selected, it will be assigned as a normally closed input. Proceed with caution as this may
cause the engine to start. If an alarm signal is chosen, it can be configured on the next page (Enabled, NO/NC,
Audible, Importance (Alarm or Warning). The available signals are:

- Low Fuel Level, High Fuel Level, Fuel Tank Leak

- Water Reservoir Empty, Water Reservoir Low, Water Reservoir High

- Flow Meter ON, Main Relief Valve Open

- Low Suction Pressure

- Lockout

- Remote Manual Start

- Deluge Valve Start (NC)

«
...
25
26
27
28
29
...
»

Содержание HFD

















































Отзывы:

Нет отзывов