Tornatech HFD Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 48

Tornatech HFD Скачать руководство пользователя страница 37

37

These pages allow to configure the Lockout input and the interlock output parameters. To be active, those options
need to be assigned to an Input or an Output on the I/O board.

Lockout is an Input that disables the engine from starting.
- Enable in emergency: If checked, this option will prevent the electronic assistance on an Emergency start.
- Enable in manual mode: If checked, this option will prevent the Manual start.
- Enable in automatic mode: If checked, this option will prevent the Automatic start.
- Enable in remote manual mode: If checked, this option will prevent the Remote Manual start.
- Enable in "start/stop" mode: If checked, this option will prevent the "start/stop" mode.
- Shutdown Engine: If enabled, the lockout signal will also act as a shutdown and will stop the engine if it is running.

Interlock is an Output that prevents a second engine from starting.
- Enable in emergency: If checked, this option will activate the output "interlock" on an Emergency start.
- Enable in manual mode: If checked, this option will activate the output "interlock" on a Manual start.
- Enable in automatic: If checked, this option will activate the output "interlock" on a Automatic start.
- Enable in Remote Manual mode: If checked, this option will activate the output "interlock" on a Remote Manual
start.
- Enable in "start/stop" mode: If checked, this option will activate the output "interlock" on a "start/stop" mode.
- Engine Run required: If enabled, the controller will wait to have the Engine Run signal before activating the
Interlock output.

«
...
35
36
37
38
39
...
»

Содержание HFD

















































Отзывы:

Нет отзывов