Tormach ATC Скачать руководство пользователя страница 6

Страница: 6 / 22

2. Secure the air cylinder to the ATC main assembly with a 12

mm hex wrench (provided) and two M14 × 20 mm socket

head cap screws.

Figure 2-14: Putting the air cylinder hardware into the air

cylinder.

3. Connect the air lines from the ATC main assembly to the air

cylinder as follows:

Connect the short air line to the front of the cylinder.

Connect the long air line to the back of the cylinder.

Mount the Automatic Tool Changer (ATC) Bracket

1. Identify the four provided standoffs that are used to mount

the ATC to the Z-column:

Three fixed standoffs

One tilt standoff

2. Remove the flange nuts and the washers from the standoffs,

and then set them aside.

3. Identify and remove the four set screws on the Z-column with

a flat-blade screwdriver.

4. Install the four standoffs on the Z-column as shown in the

following image.

Figure 2-15: Four standoffs installed on the Z-column.

5. Securely tighten the standoffs on the Z-column with a 1-1/2

in. adjustable wrench.

6. Put the ATC mounting bracket on the standoff's threaded

studs as shown in the following image.

Figure 2-16: ATC mounting bracket moving on to the four

standoffs.

Note:

Verify that the tilt standoff's eccentric cam fits

into the large slot on the ATC mounting bracket.

7. Secure the bracket by reinstalling the washers and flange nuts

that you removed in Step 2 with a 13 mm socket.

8. Pull the bracket toward the front of the machine. You'll make

adjustments to the location of the bracket later in this

procedure, but we recommend starting with it moved

forward.

Install the Main Assembly

1. Remove the four preinstalled M8 × 1.25 - 16 mm socket head

cap screws and washers from the bottom of the ATC electrical

cabinet. Then, set all aside for later use.

CAUTION!

Team Lift Required: You must have the

aid of more than one person to lift and move the

object. The object is heavy, and lifting it by yourself

can cause serious injury.

Page 6

©Tormach® 2019
Specifications subject to change without notice.

tormach.com

TD10559: Owner's Guide: M ATC Retrofit for PCNC 1100 Series 3 (1119A)

TECHNICAL DOCUMENT

Содержание ATC























Результаты поиска

Содержание ATC

Отзывы:

Похожие инструкции для ATC

Бренды по названию

Популярные бренды

Tormach ATC, Руководство пользователя

Результаты поиска

Содержание ATC

Отзывы:

Похожие инструкции для ATC

Бренды по названию

Популярные бренды