Tormach ATC Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 22

background image

9. Remove wire T1 from the VFD, and then insert it in to the

open slot in the T1 lever nut on the ATC Legacy Adapter Cable.

Note:

If you have an (optional) load meter, your

VFD has an extra wire in slot T1. Remove it from the

VFD, and then insert it into the remaining open slot

in the T1 lever nut on the ATC Legacy Adapter Cable.

10. Completely push the lever down on the T1 lever nut to latch

the wire. Verify that the lever is latched.

11. Connect the loose wire from the T1 lever nut in to slot T1 on

the VFD.

Figure 2-34: T1 lever nut connected to slot T1 on the VFD.

12. Connect the loose wire from the B3/B5 lever nut on the

ATC Legacy Adapter Cable to slot B3 on the VFD.

Note:

If you have an (optional) load meter, your

VFD has an extra wire in slot B3. Remove it from the

VFD, and then insert it into the remaining open slot

in the B3/B5 lever nut on the ATC Legacy Adapter

Cable.

13. Replace the VFD faceplate.

14. Identify the green and yellow ground wire on the ATC Legacy

Adapter Cable. Then, route it through the wire troughs toward

the ground terminal block.

Figure 2-35: Terminal block in the electrical cabinet.

15. Connect the ground wire in to any open slot on the ground

terminal block.

Page 12

©Tormach® 2019
Specifications subject to change without notice.

tormach.com

TD10559: Owner's Guide: M ATC Retrofit for PCNC 1100 Series 3 (1119A)

TECHNICAL DOCUMENT

«
...
10
11
12
13
14
...
»

Содержание ATC























Отзывы:

Нет отзывов

Похожие инструкции для ATC

Бренд: walimex Страницы: 12

Бренд: Zebronics Страницы: 5

Бренд: MOB Страницы: 6

Бренд: AccuPower Страницы: 2

Бренд: Gardena Страницы: 14

Бренд: MayPole Страницы: 4

SOL APOLLO Series

Бренд: Solplanet Страницы: 135

Бренд: Sterling Power Страницы: 2

Бренд: Hama Страницы: 1

Бренд: RadioLink Страницы: 22

Бренд: AEG Страницы: 31

Бренд: AEG Страницы: 100

Бренд: AEG Страницы: 60

Бренд: AEG Страницы: 31

Бренд: AEG Страницы: 84

Бренд: AEG Страницы: 68

Бренд: AEG Страницы: 76

Бренд: AEG Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды