Tormach ATC Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 22

background image

Figure 2-51: Tray FWD and Tray REV buttons on the

ATC tab.

2. Select

Tray Rev

to rotate the tray counterclockwise

(backward) one full tool slot.

3. Verify that the tool’s shank is aligned with the collet in the

spindle.

4. Depending on the alignment, do one of the following:

l

Aligned

You have completed aligning the ATC. Remove

the tool from the fork. Go to "Operation" (page 19).

l

Not Aligned

You must readjust the tool tray rotation. Go

to "Adjust the Tool Tray Load Position" (page 16).

Page 18

©Tormach® 2019
Specifications subject to change without notice.

tormach.com

TD10559: Owner's Guide: M ATC Retrofit for PCNC 1100 Series 3 (1119A)

TECHNICAL DOCUMENT

«
...
16
17
18
19
20
...
»

Содержание ATC























Отзывы:

Нет отзывов

Похожие инструкции для ATC

Бренд: Hammer Страницы: 16

Бренд: Velleman Страницы: 15

Digital Duo Charge

Бренд: Balmar Страницы: 8

Бренд: Lenmar Страницы: 2

BLACK WIDOW ELITE

Бренд: Promax Страницы: 4

Бренд: Icom Страницы: 1

Бренд: Rato Страницы: 7

WAECO PerfectCharge CA360

Бренд: Dometic Страницы: 304

Бренд: Fronius Страницы: 64

Бренд: Sunforce Страницы: 1

Бренд: Thunder Страницы: 16

Бренд: NATURE & DECOUVERTES Страницы: 28

LIBERTY 1000 Series

Бренд: C&D Technologies Страницы: 43

EVERVOLT EV-BMS

Бренд: Panasonic Страницы: 30

Бренд: Makita Страницы: 8

Бренд: Zivan Страницы: 40

Бренд: Asus Страницы: 29

Бренд: Asus Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды