background image

 

www.nationalrailwaysupply.com

 1 

 

01874C 

 

 

NATIONAL 
       RAILWAY 
               SUPPLY

 

 
 
 
 
 

Operating and Service Instructions for 

VVR Portable Battery Charger

 

 

 

 

VVR PORTABLE BATTERY CHARGER 

MODEL 21120 VVR 85-60P 

 
 
 

PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS 

 

For correct operation of the equipment, it is important to read and be familiar 

with this entire manual before operating the charger. 

DO NOT DISCARD THIS MANUAL AFTER READING. 

 

 

 

LOOK FOR THIS SYMBOL TO POINT OUT SAFETY PRECAUTIONS.  IT MEANS:  
BECOME ALERT—YOUR SAFETY IS INVOLVED.  
IF YOU DO NOT FOLLOW THESE 
SAFETY INSTRUCTIONS, INJURY OR PROPERTY DAMAGE CAN OCCUR.

 

 
 
 

1.  IMPORTANT SAFETY INSTRUCTIONS 

 

a.  Before using the battery charger, read all the 

instructions and caution markings on the 
battery charger, battery, and all products 
using the battery. 

 

b.  Do not touch the uninsulated parts of the  

DC output connectors, or the battery 
terminals, as there is a possibility of 
electrical shock. 

  c. Batteries produce hydrogen gas while 

operating, which can explode if ignited. 

 

Never use an open flame, smoke, or create 
sparks in the vicinity of the battery.  Ventilate 
the area well when the battery is charging in 
an enclosed area. 

 

d.  Batteries contain caustic material that may 

cause burns.  Do not get in eyes, on skin, or 
clothing.  If the gelled or liquid content of the 
batteries contacts the skin or clothing, wash 
the area thoroughly with water.  In the case 
of contact with the eyes, flush immediately 
with clean water for 15 minutes and obtain 
medical attention. 

 

e.  The charger must be programmed for the 

proper battery voltage and amperage before 
the charge is started. 

 

f.  Verify charger display says "OFF" before 

connecting or disconnecting DC charger 
cables from battery. 

  g. De-energize all AC and DC power 

connections before servicing this unit.  If 
injury does occur, apply standard treatment 
for electrical shock and, if necessary, 
consult with a physician. 

 

h.  The charger is not for unprotected outdoor 

use.  Do not expose the charger to rain or 
snow. 

 

i. 

Do not operate the charger if it has received 
a sharp blow, been dropped, or otherwise 
damaged. 

j.  Do not disassemble the charger.  Have the 

charger examined by a NATIONAL 
RAILWAY SUPPLY service agent.  If the 
charger is assembled incorrectly, damage to 
the charger and the batteries or an electrical 
shock may result. 

 

2. OPERATING 

INSTRUCTIONS 

 

a.  Connect DC cables to battery cells to be 

charged: RED clamp to battery positive (+) 
and BLACK to battery negative (-). 

*01874*

Содержание 21120 VVR 85-60P








Отзывы: